Frank Murch's Discussions (72)

Discussions Replied To (54) Replies Latest Activity

"I think there are a number of engines at 7 L.  I think it is the max size for a raci…"

Frank Murch replied Feb 28 to Just a Thought

6 Feb 29
Reply by Tony and Ginny 429

"I might be back for the new clips, but I loaded it with dielectric grease to stop th…"

Frank Murch replied Feb 10 to rust in fuse box

6 Feb 10
Reply by Frank Murch

"I think I figured it out - The clips can be removed and then a dremel tool with a wi…"

Frank Murch replied Feb 10 to rust in fuse box

6 Feb 10
Reply by Frank Murch

"I used  House of Manifolds (760) 598-1210 2293 S Santa Fe Ave Vista, CA 92083 I also…"

Frank Murch replied Feb 1 to 63 driver side exhaust manifold needed

8 Feb 2
Reply by Tony and Ginny 429

"Getting closer- attached are the 63 pinouts,  all I need are the 1964 headlight pull…"

Frank Murch replied Jan 9 to Installing a 64 headlight switch into your 63

8 Jan 9
Reply by Tony and Ginny 429

"Here is the wiring, the colors are similar, but I do not know what poles do what fun…"

Frank Murch replied Jan 9 to Installing a 64 headlight switch into your 63

8 Jan 9
Reply by Tony and Ginny 429

"Thanks, this is helpful and it is dawning on me what to do.  I do not have Russ' dia…"

Frank Murch replied Jan 9 to Installing a 64 headlight switch into your 63

8 Jan 9
Reply by Tony and Ginny 429

"Hi Russ,  If you know - What is the 1964 headlight switch part number?  Also I would…"

Frank Murch replied Jan 9 to Installing a 64 headlight switch into your 63

8 Jan 9
Reply by Tony and Ginny 429

"There are several on ebay at the moment.  These are expensive ($100 on up).  They ca…"

Frank Murch replied Jan 7 to Driver's window won't go up. Bought new motor but mechanic says replace the hinky switch panel, and I can't find one to buy.

8 Jan 11
Reply by Jim Murphy

"Thanks, I understand the 63 was designed for a plastic window, but the plastic alway…"

Frank Murch replied Jan 6 to glass rear window for a convertible top

4 Jan 6
Reply by Tony and Ginny 429

RSS

Photos

  • Add Photos
  • View All

Forum

Bendix Power Brake Unit Power Section

Started by Mathis Richter in 1963/64 Cadillac Specific Discussion. Last reply by Chris Codd yesterday. 7 Replies

Hi,I have a huge problem my POWER SECTION of the ``Master-VAC Power Brake unit 9´´Diameter ´´ from Bendix is Broken and I can't open it to replace al the rubber parts did some of you have auch Power…Continue

Third brake light -help please.

Started by paul k in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 8 Replies

Did anybody from the club install third brake light in the rear window in his Cadillac? I have problem to figure out how to do it. Can I just run wire from break pedal switch and second wire connect…Continue

Extra speakers in the cadillac.

Started by paul k in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

Ok, I have another question. Since I will run wire for a brake light I might run speakers wires.I would like to install 2 extra speakers or maybe 4. What is best option. I do have 2 speakers already-…Continue

429 and 400 trans. for sale

Started by Mark C Bills in For Sale. Last reply by Tony and Ginny 429 on Monday. 6 Replies

I have an excellent running 429 with 400 trans.recently removed from my 64. It has electronic ignition, new water pump,new fan and clutch(not pictured),new fuel pump,Holley 650 vac. sec. carb. with…Continue

Blog Posts

1964 Cadillac Fleetwood sixty special / transmission dipstick needed

Posted by Pablo on September 20, 2020 at 9:57pm 1 Comment

How are you doing folks, I’m looking for a transmission dipstick, any info I will appreciated, thank you very much

1963 Cadillac hood driver side hinge

Posted by Steven on September 16, 2020 at 9:23am 1 Comment

Hello,

 Does anyone know were I can buy a 1963 Cadillac hood driver side hinge or is there any other hinge that would fit? 

Thanks

Steven

Bad Guage?

Posted by Karl Schwarz on August 26, 2020 at 3:08pm 6 Comments

So I am troubleshooting my fuel gauge issue. I bought a new sender and tested it. It  it goes from 1-ohm (empty) to 35-ohm (full). When I test it (outside the tank), when the float is in the up (full) position it only moves the gauge to about 1/2 full. When at the bottom (empty) position the gauge shows empty. This is the same issue I have when I fill and then use the gas in the tank - the gauge never reads ore than half full. Based on what I've read on this thread it would seem like the…

Continue

Website

Posted by Fritz Seitz on August 11, 2020 at 2:35am 0 Comments

I have been working on a website-----www.fritzsautorepair.com-----

Does anyone have suggestions?

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service