Dan McNarry's Discussions (139)

Discussions Replied To (128) Replies Latest Activity

"I've had custom exhaust gaskets made for radial aircraft engines in both grafoil and…"

Dan McNarry replied May 31 to Exhaust Manifold Gaskets......Again

22 Jun 2
Reply by Mack

"Tony, the new to me peace of mind regarding my fuel was put to the test today. We to…"

Dan McNarry replied May 30 to Caddy Daddy

10 May 30
Reply by Dan McNarry

"Nice job fabricating your gaskets. Here is a pretty good option that I use. They are…"

Dan McNarry replied May 30 to Exhaust Manifold Gaskets......Again

22 Jun 2
Reply by Mack

"Russ, I installed the sending unit yesterday afternoon and went and filled the car u…"

Dan McNarry replied May 30 to Caddy Daddy

10 May 30
Reply by Dan McNarry

"You could try Auveco.com. I bought several pounds of bolts from them when I rebuilt…"

Dan McNarry replied May 25 to bolts and hardware

2 May 25
Reply by Jason Edge

"Anders, I just looked on Rockauto's web site at an image of a 64 gasket and see that…"

Dan McNarry replied May 25 to Oil Pan Gaskets

17 May 26
Reply by Kim K Kaiser

"Thanks Tony. I went ahead and put the pan on this afternoon after first putting the…"

Dan McNarry replied May 24 to Oil Pan Gaskets

17 May 26
Reply by Kim K Kaiser

"I watched that last night. Man, did he ever cram a lot of stuff in that thing! Glad…"

Dan McNarry replied May 23 to 24 Years in a Canadian Garage!

10 May 23
Reply by Dan McNarry

"The only logical repair is a heli coil. If you drill it out and tap it to a larger s…"

Dan McNarry replied May 13 to So how bad does this look

32 May 13
Reply by Russ Austin

"It appears to be the door activated switch circuit for courtesy lamps."

Dan McNarry replied May 13 to Wiring Diagrams Question

4 May 13
Reply by Tony and Ginny 429

RSS

Photos

  • Add Photos
  • View All

Forum

Intake manifold gasket leak

Started by Joe DiIaconi in Restoration Discussion. Last reply by Tony and Ginny 429 9 hours ago. 1 Reply

Hello Cat's & Kitten's :) Happy Turkey Day ! I believe I have an intake manifold leak. The last time I bought an intake manifold gasket with the chock port blocked from Olson's gasket's. This…Continue

Happy Thanksgiving to all of our 1963/64 Cadillac Chapter & Website Members!

Started by Jason Edge in General Discussion. Last reply by Tony and Ginny 429 14 hours ago. 3 Replies

Earlier Fall Picture with 'Dino'I just wanted to wish all of our US…Continue

Tags: Thanksgiving, Happy

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 19 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Dipstick tube

Started by JOHN V SCHILLACI in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 3 Replies

Hello, Does anyone know off hand if the dipstick tube can be changed without the removal of the oil pan?  It's a 1964 Cadillac De Ville ConvertibleContinue

Blog Posts

Picture of ignition switch

Posted by Cees de Bunje on November 27, 2020 at 6:20am 0 Comments

Does anyone have a close-up picture of the ignitionswitch with keys in it made in landscape format? Switch must be in dashboard. Many thanks in advance. Cees.

1964 Cadillac Fleetwood sixty special / transmission dipstick needed

Posted by Pablo on September 20, 2020 at 9:57pm 1 Comment

How are you doing folks, I’m looking for a transmission dipstick, any info I will appreciated, thank you very much

1963 Cadillac hood driver side hinge

Posted by Steven on September 16, 2020 at 9:23am 1 Comment

Hello,

 Does anyone know were I can buy a 1963 Cadillac hood driver side hinge or is there any other hinge that would fit? 

Thanks

Steven

Bad Guage?

Posted by Karl Schwarz on August 26, 2020 at 3:08pm 6 Comments

So I am troubleshooting my fuel gauge issue. I bought a new sender and tested it. It  it goes from 1-ohm (empty) to 35-ohm (full). When I test it (outside the tank), when the float is in the up (full) position it only moves the gauge to about 1/2 full. When at the bottom (empty) position the gauge shows empty. This is the same issue I have when I fill and then use the gas in the tank - the gauge never reads ore than half full. Based on what I've read on this thread it would seem like the…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service