William Cameron's Discussions (55)

Discussions Replied To (52) Replies Latest Activity

"Hi Jim, thx for the compliment! I have the same issues with the boot or the top not…"

William Cameron replied Jun 19 to Wanted to Buy

10 Jun 20
Reply by Tony and Ginny 429

"Hi Jim, the guy that just bought a deck lid used "uship"  it did happen to be a movi…"

William Cameron replied Jun 18 to Wanted to Buy

10 Jun 20
Reply by Tony and Ginny 429

"Hi Jim, I have two lids, both from solid southwestern cars, surface rust on exterior…"

William Cameron replied Jun 18 to Wanted to Buy

10 Jun 20
Reply by Tony and Ginny 429

"did you find a rear deck lid? I have one from a 64' SDV if you're still lookiing"

William Cameron replied Jun 17 to Wanted to Buy

10 Jun 20
Reply by Tony and Ginny 429

"I've got a couple of wiper motors from 1964 cadillacs if you're still looking for one"

William Cameron replied Jun 16 to Wiper Motor 1964 DeVille

6 Jun 16
Reply by William Cameron

"great story and beautiful car ! "

William Cameron replied Mar 30, 2018 to APRIL NEWSLETTER SNEAK PEAK #4.

10 Mar 30, 2018
Reply by Tony and Ginny 429

"I have a full set, clean and rust free if you're anywhere near Colorado"

William Cameron replied Mar 30, 2018 to steel rims

4 Mar 30, 2018
Reply by William Cameron

"Hello Alex, your request for a passenger side door for CDV and convertible is still…"

William Cameron replied Jul 28, 2017 to Looking for a rust free Passenger door for 64 Convertible /Coupe

1 Jul 28, 2017
Reply by William Cameron

"The rear deck lid is yours Tim if you can arrange a pick up and transport for it"

William Cameron replied Mar 20, 2017 to Seeking a decent trunk with minimum rot

27 May 22, 2017
Reply by Mark Borer

"If Chad doesn't have an oil pan, I have one in VG condition for a 1964 429 engine. y…"

William Cameron replied Mar 20, 2017 to 1964 429 engine parts

6 Mar 20, 2017
Reply by Chad Jones

RSS

Photos

  • Add Photos
  • View All

Forum

looking for a 429 heat riser and cruise control unit

Started by Christian Doerk in Wanted to Buy. Last reply by Kurt 50 minutes ago. 1 Reply

I am looking for a functioning heat riser valve and a cruise control for a 1964 Cadillac.In principle, the heat riser flap does not have to work. It is only important that the spacer / housing is not…Continue

Tags: exhaust, riser, heat, control, cruise

Winter time cruise in Australia.

Started by Kevin Campbell in General Discussion. Last reply by Jason Edge 2 hours ago. 3 Replies

The weather here in winter is great for a Cadillac cruise.Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 2 hours ago. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Free 1964 parts before I throw them out

Started by Preston Bealle in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin yesterday. 7 Replies

I have front brake drums and discs, a window, a window frame, and an air cleaner shroud. I don't need them and anyone can have them for shipping cost. I would guess the shipping would be $20-25 for…Continue

Blog Posts

64 Power Servo vacuum leak

Posted by Kent Prows on June 27, 2020 at 4:02pm 0 Comments

I finally got around to fixing a leak in my heater core.  I decided to check to see if there were any other obvious issues while I had everything torn apart.  When I put a vacuum directly (bypassing the transducer) to the power servo it gets to about 10" and then slowly leaks back to zero.  The fan will not go to full and the mode door will not open completely.  I have read a couple of other posts that said they repaired the power servo leaks.  How?  Does anyone have one to sell?  I just…

Continue

63 Caddy Horn

Posted by Robert Alan Shannon on May 27, 2020 at 9:25am 9 Comments

 Just noticed a 1963  Caddy trumpet horn on Ebay. No part # given but some of his other items are 1963 specific, just throwin this out there, I have no connection to this listing .

Wiring connection help.

Posted by Jimmy Davis on May 24, 2020 at 9:15pm 2 Comments

Can someone help me figure where these connections go? I have a 64 60 special if it matters.…



Continue

Wood grain finally done.

Posted by Jimmy Davis on May 20, 2020 at 4:57pm 3 Comments

After years of wanting to, I finally redid my wood dash paneling on my 64 60s. Not too hard to do either.…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service