Ben Roberts's Discussions (20)

Discussions Replied To (14) Replies Latest Activity

"Seems like you are very committed.  Glad to hear you are saving her. The original pa…"

Ben Roberts replied Apr 6 to 1963 Series 62 Conv sitting for 27 years...covering all the bases??

14 Apr 6
Reply by Ben Roberts

"Thanks for the feedback.  It turns out it was just a few hundred dollars more for a…"

Ben Roberts replied Feb 11 to Recommended rebuilder for 63 Convertible's brake booster?

6 Feb 11
Reply by Ben Roberts

"Engine is well documented at 83,000 original miles from the one owner.  Everything h…"

Ben Roberts replied Jan 30 to New timing chain and gears...how much slack?

11 Jan 31
Reply by Anders

"Thanks for reviewing.  Also, I did not see an oil slinger on this at disassembly.  C…"

Ben Roberts replied Jan 30 to New timing chain and gears...how much slack?

11 Jan 31
Reply by Anders

"Thank you for the feedback Russ"

Ben Roberts replied Jan 30 to New timing chain and gears...how much slack?

11 Jan 31
Reply by Anders

"Russ, Thank you for the feedback"

Ben Roberts replied Jan 23 to How much play in 63 timing chain?

6 Jan 23
Reply by Ben Roberts

"Thanks for the feedback.  New parts it is."

Ben Roberts replied Jan 23 to How much play in 63 timing chain?

6 Jan 23
Reply by Ben Roberts

"Thank you for the encouragement.  It all came out fine with the shallow holes.  I'm…"

Ben Roberts replied Jan 17 to Harmonic balancer holes are too shallow for the 3 bolts of puller

3 Jan 17
Reply by Ben Roberts

"Is the power steering fluid ATF? I need to look up how to vacuum test a booster."

Ben Roberts replied Jan 8 to 1963 Series 62 Conv sitting for 27 years...covering all the bases??

14 Apr 6
Reply by Ben Roberts

"You answered a question I failed to ask earlier.  Yes, I will spin the oil pump to c…"

Ben Roberts replied Jan 8 to 1963 Series 62 Conv sitting for 27 years...covering all the bases??

14 Apr 6
Reply by Ben Roberts

RSS

Photos

  • Add Photos
  • View All

Forum

Bendix Power Brake Unit Power Section

Started by Mathis Richter in 1963/64 Cadillac Specific Discussion. Last reply by Chris Codd yesterday. 7 Replies

Hi,I have a huge problem my POWER SECTION of the ``Master-VAC Power Brake unit 9´´Diameter ´´ from Bendix is Broken and I can't open it to replace al the rubber parts did some of you have auch Power…Continue

Third brake light -help please.

Started by paul k in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 8 Replies

Did anybody from the club install third brake light in the rear window in his Cadillac? I have problem to figure out how to do it. Can I just run wire from break pedal switch and second wire connect…Continue

Extra speakers in the cadillac.

Started by paul k in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

Ok, I have another question. Since I will run wire for a brake light I might run speakers wires.I would like to install 2 extra speakers or maybe 4. What is best option. I do have 2 speakers already-…Continue

429 and 400 trans. for sale

Started by Mark C Bills in For Sale. Last reply by Tony and Ginny 429 on Monday. 6 Replies

I have an excellent running 429 with 400 trans.recently removed from my 64. It has electronic ignition, new water pump,new fan and clutch(not pictured),new fuel pump,Holley 650 vac. sec. carb. with…Continue

Blog Posts

1964 Cadillac Fleetwood sixty special / transmission dipstick needed

Posted by Pablo on September 20, 2020 at 9:57pm 1 Comment

How are you doing folks, I’m looking for a transmission dipstick, any info I will appreciated, thank you very much

1963 Cadillac hood driver side hinge

Posted by Steven on September 16, 2020 at 9:23am 1 Comment

Hello,

 Does anyone know were I can buy a 1963 Cadillac hood driver side hinge or is there any other hinge that would fit? 

Thanks

Steven

Bad Guage?

Posted by Karl Schwarz on August 26, 2020 at 3:08pm 6 Comments

So I am troubleshooting my fuel gauge issue. I bought a new sender and tested it. It  it goes from 1-ohm (empty) to 35-ohm (full). When I test it (outside the tank), when the float is in the up (full) position it only moves the gauge to about 1/2 full. When at the bottom (empty) position the gauge shows empty. This is the same issue I have when I fill and then use the gas in the tank - the gauge never reads ore than half full. Based on what I've read on this thread it would seem like the…

Continue

Website

Posted by Fritz Seitz on August 11, 2020 at 2:35am 0 Comments

I have been working on a website-----www.fritzsautorepair.com-----

Does anyone have suggestions?

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service