Russ Austin's Discussions (2,444)

Discussions Replied To (2217) Replies Latest Activity

"Not sure what tranny you had in the 65 limo, but I have a 64 limo drive shaft.  The…"

Russ Austin replied Aug 2, 2014 to 500 Swap into Commercial Chassis

14 Aug 3, 2014
Reply by Shorty

"Were they working correctly before?  if they were not, I would guess that the wiper…"

Russ Austin replied Jul 26, 2014 to Wiper Motor will not "Park" wipers in correct Position.

13 Jul 30, 2014
Reply by Dan Benck

"Same with me, fresh out. Better get that starter brace, just as hard to find."

Russ Austin replied Jul 26, 2014 to Wanted to buy 64 deville transmission parts

6 Jul 30, 2014
Reply by Mark S Anderson

"30 over is just fine."

Russ Austin replied Jul 24, 2014 to 64' 429 engine rebuild

11 Jul 24, 2014
Reply by Russ Austin

"I use the 2 O-rings, small amount of blue or orange RTV, and the washer trick.  http…"

Russ Austin replied Jul 24, 2014 to Water pump riser

3 Jul 24, 2014
Reply by Todd Lentz

"Since your asking for opinions, I would go bone stock quiet.  But if you insist, flo…"

Russ Austin replied Jul 24, 2014 to 64' 429 engine rebuild

11 Jul 24, 2014
Reply by Russ Austin

"What was the block bored out to?"

Russ Austin replied Jul 23, 2014 to 64' 429 engine rebuild

11 Jul 24, 2014
Reply by Russ Austin

"Look forward to the innovation update."

Russ Austin replied Jul 17, 2014 to 1964 Deville 429 Sanderson Header installation

27 Jan 4, 2019
Reply by Mark Beecher

"no probs with blowing air through. Its open all the way through, to the bottom of th…"

Russ Austin replied Jul 16, 2014 to hand choke

4 Jul 16, 2014
Reply by Russ Austin

"Inside the choke tube in the manifold, is a twisty piece of metal. It suppose to be…"

Russ Austin replied Jul 16, 2014 to hand choke

4 Jul 16, 2014
Reply by Russ Austin

RSS

Photos

  • Add Photos
  • View All

Forum

Input appreciated on a transmission issue

Started by Tosh Dickenson in General Discussion. Last reply by Tosh Dickenson 29 minutes ago. 6 Replies

Finally a sunny day to drive the Caddy into work!Alas when I set off down the road, I realized she wasn't shifting from first to any higher range.  I just drove it on Saturday and it was shifting…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Tony and Ginny 429 57 minutes ago. 5 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Convertible Top Cylinder Removal

Started by Brian Wiseman in 1963/64 Cadillac Specific Discussion. Last reply by Brian Wiseman 2 hours ago. 4 Replies

Just wanted to check before removing my 1964 convertible top cylinders.  I have the instructions from the 1964 shop manual.  I have identified, in Red #s, the bolts in the procedure with the images. …Continue

Bucket seats

Started by Gregory Lewis Freeman in 1963/64 Cadillac Specific Discussion. Last reply by Gregory Lewis Freeman 6 hours ago. 3 Replies

I'm looking fo a set of 63 64 eldo or devilleBuckets with console and door seat controllersGreg 2133059550.Continue

Blog Posts

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…

Continue

Road Trip

Posted by Ray Schick on January 21, 2020 at 9:00pm 7 Comments

Got a little cabin fever this morning,decided to take a road trip to Hickory Corners Michigan, The Gilmore Museum. It’s about 2 1/2 hours from my home . Place is awesome,I was really impressed.

9A648CFF-E965-4CE0-8E91-8E194AC70DED.jpeg…



Continue

1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…

Continue

Looking for the Rochester Choke Tube ...

Posted by Mack on January 10, 2020 at 1:14am 3 Comments

37E244B6-71C7-4857-8D50-1BD8C48077A4.jpeg

Looking to buy the choke tube for my Rochester... anybody have one for Sale???

Events

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service