All Discussions Tagged '429' (6)

Discussions Replies Latest Activity

Exhaust manifold: Repair, replace or headers?

My newly acquired '64 Coupe DeVille suffers from a cracked right side exhaust manifold. It looks like my options are limited to rolling the…

Started by Dutch Dickinsen

3 30 minutes ago
Reply by Dutch Dickinsen

1964 Deville 429 Sanderson Header installation

I am installing  Sanderson Headers in a 1964 Deville. Cracked exhaust manifolds and no replacements out there.  Ran into a major hurdle wit…

Started by Mike Miller

27 Jan 4
Reply by Mark Beecher

Installing exhaust flex pipe to reduce vibration on manifold?

After checking my Fleetwood for the upcoming season and our Cadillac Club meeting in May unfortunately I found three!! 1 to 1 ½ inch cracks…

Started by Christian Doerk

2 Apr 23, 2018
Reply by Christian Doerk

Wanted 1964 Sedan de Ville engine block

Dear all, Looking for a good 1964 short block or complete 429 engine. Inner parts are not a must. Hope to hear your soonest reply. Thanks

Started by Clifford Muskus

7 Oct 29, 2017
Reply by JOHN V SCHILLACI

Boring out the 429

Any idea what is the max you can bore out a 429 engine block ? How many cubic inches would that be when completed If just bored to clean u…

Started by Tony and Ginny 429

2 Feb 11, 2017
Reply by Tony and Ginny 429

1964 Cadillac Sedan Deville 4(door) 429 7.0

429 ,7.0 - hi guys sorry i have been M.I.A had a lot going on , personal life . thank god now everything is looking good . yet i need a dri…

Started by Edward

3 Nov 14, 2016
Reply by Edward

RSS

Photos

  • Add Photos
  • View All

Forum

Exhaust manifold: Repair, replace or headers?

Started by Dutch Dickinsen in General Discussion. Last reply by Dutch Dickinsen 30 minutes ago. 3 Replies

My newly acquired '64 Coupe DeVille suffers from a cracked right side exhaust manifold.It looks like my options are limited to rolling the dice on a used manifold, converting to headers or seeing if…Continue

Tags: 429, manifold, exhaust

Steering Wheel

Started by Mark Borer in General Discussion. Last reply by Tony and Ginny 429 58 minutes ago. 1 Reply

plz watch this videoIt shows play between the 2 cylinders that make up my columni have tightened everything up as best as I can....but it moves a bitthe lower cover had a screw that lined it up, and…Continue

A Drilling No-No .... That Worked!

Started by Jason Edge in General Discussion. Last reply by Jason Edge 9 hours ago. 16 Replies

Thought I would share a quick story regarding something I did that I generally do not recommend - Free handed drilling a broken front engine cover bolt.  Before I jump into it I will say I do not…Continue

Help! I need a 1964 Eldorado front left fender.

Started by Jorge M in Wanted to Buy. Last reply by Jon Ettman 20 hours ago. 5 Replies

Help looking for a 1964 Eldorado front fender for a convertible.Thank you please contact djjmoreno84@gmail.comContinue

Blog Posts

Starter Solenoid replacement-how difficult? Where to buy?

Posted by Norman Silverman on August 20, 2019 at 8:24pm 6 Comments

Hello All.

I believe the starter solenoid has gone bad in my 64 DeVille. When I turn the key, often all I get is a click, then if I try a few times again the starter turns perfectly. All battery cables are on tight and the battery is good. So, I believe this problem is the solenoid. Where do I buy the right solenoid and is it necessary to remove the starter in order to swap it out? …

Continue

Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…

Continue

Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.

Thanks

Dominic

Upper A Arm Rubber Bumpers

Posted by Gene McIlroy on August 12, 2019 at 1:30pm 3 Comments

I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service