Hi the  390 motor in my 1963 Coupe is toast and can not be repaired. I am in need of either a complete motor or small block or big block any block. I have tried most of the advertised parts dealers on the site but no luck. Any help in finding one would be greatly appreciated. 

Views: 79

Reply to This

Replies to This Discussion

The parts you are looking for —may be available right here when the boys come by 

Enjoy 

Not sure what you mean by when the boys come by in  your reply. Thanks.

He's referring to Jason and Russ.

You must've done a number on the 390 for it to be unrepairable. Did it throw a leg out of bed?

I bought the car as is knowing that there was a problem with the motor. When I tore it apart,  I found out that a piston had disintegrated and the connected rod when through the cylinder leaving a two inches hole. Now I have to replace it or rebuild one with the good parts that are left.

Holes in the block, geez, some bondo and chemi weld and you're going again. LOL

Since I reside in Eastern Canada I was thinking more likes duck tape or hockey tape LMAO. But I do have my work cut out. It's a long winter here so I have time on my hand to get the motor ready for spring.

Hehe, "duck tape" is a bit funny. However where I live its called "Strömma tape". Strömma is a large passenger vessel company and, according to the rumour, they are famous for repairing everything on their boats with the gray sticky tape originally named duct tape.

Picture of Strömmas Östanå in a wintry Stockholm archipelago:

Btw Kevin, when you get here an archipelago cruise is on the schedule. However not with Strömma. We will take a steam boat cruise on Storskär eating steam boat steak.

For those that doesn't know, steam boat steak is a tender piece of meat that is put on the coal shovel and into the furnace of the boiler for a few seconds. Tastes a bit weird and sooty. Well worth it for a motor head.

I have bare blocks, short and long blocks.   My email is  russ85747@hotmail.com    Located in Tucson AZ

Hi Russ. We have communicated already by e-mail on Sunday. I will send you another reply by e-mail and see if we can work something out. 

 Marcel

I am sure you now understand what  I meant  by the boys stopping by as we have the regular crew that lives here and drop in very often to help others out with parts and hands on advice 

Do acquire any parts you may be needing from Russ as he has been doing great business since I am on this site as a consultant  ( 3-4 times ) daily since 2006 

Anything Jason can do for you will be golden as well 

These guy live and breath our year cars with the knowledge to get you the correct item at the right price 

Enjoy 

Thanks I will get in touch with Russ.

RSS

Photos

  • Add Photos
  • View All

Forum

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 2 minutes ago. 166 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Cadillac King - UNFAIR, Unprofessional

Started by Edward in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 12 minutes ago. 9 Replies

Hi Good America Today I’ll like to bring awareness, and hope to help prevent future headaches. 20years and they still got my order wrong !At Cadillac King i spent over 1400$ on parts. I specifically…Continue

Rear main Follow up replacement and repair,,

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 38 minutes ago. 67 Replies

Well, got it all together,, Jason, i was looking in the wrong chapter in the manual on the starter,, got that figured out.  everything hooked back upGot it put back together, started up, and oil…Continue

Movie Star Cars.

Started by Kevin Campbell in General Discussion. Last reply by Kevin Campbell 9 hours ago. 19 Replies

We have the Village Roadshow film studios about an 1.5 hour drive away.They've put out a call for cars to appear in a movie about Elvis. :-)So, I nominated our 64 Fleetwood as a potential "Movie Star…Continue

Blog Posts

Stuck at two red (dash) lights!

Posted by Jeff Kinzler on November 3, 2019 at 10:00pm 9 Comments

I hope someone can help solve these two electrical problems that appeared one after the other.

By way of background: The car, a '64 Eldorado has very limited use. It was at a restoration shop for 15 months until last January-  that supposedly did a bunch of wiring repairs including rebuilding the gas gauge that still hasn't worked properly, and the clock that hasn't worked, and re-soldering the broken wires in the drive door. All window and seat controls appear to be…

Continue

driveshaft help

Posted by wayne weaver on October 9, 2019 at 4:41pm 1 Comment

can anyone help me with a driveshaft ? I have a 1963 Cadillac 62 series 4dr with the hydro-matic trans. I need the male splined shaft on the front of the rear driveshaft section. the piece with the nut attached by clip.id be willing to buy a shaft if its not horribly priced.

Dash removal

Posted by Jake Mickley on October 9, 2019 at 12:06am 9 Comments

Hello everyone,

On a 63 CDV, if a guy wanted to remove the entire dash to get all the metal painted, and do some other things behind there, how would he go about doing that?  I checked here and the shop manual, but can't find a complete guide.

As always, and help or direction is appreciated.  Thanks!

--Jake

Introducing myself

Posted by Gary Marchand on October 7, 2019 at 9:32pm 8 Comments

Thanks for letting me join the club.  Picked up this ‘64 Coupe Deville a few months ago out of Beverly MA, the car has few stickers on it from various Cadillac clubs, didn’t know if anyone might recognize it from it’s “Glory days.” Everything seems pretty healthy except for the body and some very Mickey Mouse repairs, was wondering if anyone had any leads on…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service