I noticed that the previous owner of my 63 Coupe had condemned the Vapour return line (390 motor) by sealing it. Is this line necessary to be hooked up for proper functioning? Thanks.

Views: 88

Reply to This

Replies to This Discussion

If you are talking about the smaller fuel line on top of the fuel filter housing, then yes, that is a fuel return line to the tank. It is not a necessity, but it does help with preventing vapor lock. 

Thank you Russ. What do you mean by vapor lock and what does it do? In the mean time I will start looking for the proper housing as the fuel housing on the car does not have the additional port to reconnect the hose.

Marcel, vapor lock is when the fuel in the fuel line becomes vaporize and blocks the flow of fuel. This happens in the engine compartment. The return line keeps the flow of fuel through the fuel lines and helps reduce the chances of vapor lock.

Depending in your climate, it may not be needed. Hotter climates tend to benefit from a return line.

 Marcel 

Vapor lock is a condition that prevents you from being able to start the car caused by  a heat build  up in the engine to keep it simple 

My  64 gas return line has been disconnected for over 45 years with no issue at all effecting how the car performers 

My own opinion for what it’s worth is the return line is of no value  at all and not sure if it would prevent Vapor  lock  if that happened that I only experienced once I a 1952 Cadillac CDV that was my fathers 

I myself do not know of any other make or year cars that have the gas return line design  built into them but our year Cadillacs but that does not mean there are no others 

Your need to be stock above all could be a consideration depending on your own needs 

Your car and your call !

Enjoy 

Thanks for the valuable information. The shop manual stipulates that super gas is recommended for fuel for the 63 Caddies. Now that was back in 1963. Is it safe to drive on regular gas now.  

Most of these cars will run fine on 92 or 93 Octane. Check out this Help Page link, listed under Octane for more info: http://6364cadillac.ning.com/photo/octane?context=user

Thanks Jason again great info.

RSS

Photos

  • Add Photos
  • View All

Forum

Start up. 1st attempt

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kim K Kaiser 1 hour ago. 16 Replies

No Description

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 4 hours ago. 233 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

64 Horns

Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 1 Reply

I have 3 horns and the only one working is the bottom long one. The 2 round ones are not. I played around with the connections and they seem ok. I tried to check for power but not sure I was doing it…Continue

Compression test

Started by Michael Chomout in Restoration Discussion. Last reply by Karl Schwarz on Friday. 8 Replies

Dear Gents, just had time to dova compression test on the 429 engine by warming up the engine and removed all plugs and went through cranking without pouring oil into the cylinder since I want to…Continue

Blog Posts

63 Trunk detail

Posted by Bob Pontius on April 8, 2021 at 3:07pm 1 Comment

Jason, I liked the detail and information you have provided. I would like to do mine similar to yours. Can you help? Do you have trunk material? OPGI is sending the trunk product for my 63 Fleetwood. But it does cover the entire trunk as yours was done. If you do not have can you give me a reference? Thanks!! Bob

Car lift and jack stands

Posted by Les Eastling on March 23, 2021 at 10:00am 4 Comments

I mentioned during the 63/64 chapter zoom meeting on 3/21 that we had installed a car lift in our garage. Someone asked what kind and I didn't have the info at hand, so here is a link to it and also a link to some tall jack stands we use to add more stability to the car and an additional safety factor. There is something about getting underneath one of these cars that makes me a little nervous! …

Continue

Leaky Freeze Plug

Posted by Lee Martin on March 22, 2021 at 12:49pm 7 Comments

Just developed a significant leak coming from a freeze plug right over the starter.  Would this be considered a "cam plug" i.e. like Dorman 17616DS?  Our cars have multiple sizes of plugs on engine block and I want to get the right one.  Also, does anyone know how pricey this is for a shop to fix?  Thanks!

Balancer location

Posted by Kim K Kaiser on March 20, 2021 at 4:47pm 6 Comments

Readi g another thread. Does this look about right on balancer gap? Thats a 1/4 thick piece of metal.

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service