I went to check the fluid in the transmission on my 1963 Series 62 convertible and when I pulled on the dipstick ring the whole tube came out. I got it back in the hole, sort of, but it is loose. Anyone else have similar issue and any tips on how to get it seated back in tight? I don't have a lift or an easy way to lift the car and safely get under it.

Views: 28

Reply to This

Replies to This Discussion

The oil dipstick tube bolts to the passenger side exhaust manifold. Did you see a metal tab on the tube with a bolt hole it in it?? If not, it may have broken off. There is also an o-ring inside the the transmission housing where the dipstick tube is inserted. If the o-ring is bad or missing and the tube is not bolted in properly, the transmission will leak like a sieve when the car is parked. Been there, done that.

RSS

Photos

  • Add Photos
  • View All

Forum

1963 Cadillac Convertible Door Jamb Switch

Started by Lee Martin in 1963/64 Cadillac Specific Discussion. Last reply by Lee Martin 14 hours ago. 3 Replies

Okay, it's "dumb question time!"  Here's mine:  Does anyone know the part number for the 63 convertible door jamb switch (3 prong)?  I cannot find this in the manual...thanks!Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Rear main Follow up replacement and repair,,

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kim K Kaiser on Thursday. 38 Replies

Well, got it all together,, Jason, i was looking in the wrong chapter in the manual on the starter,, got that figured out.  everything hooked back upGot it put back together, started up, and oil…Continue

STEERING GEAR

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Wednesday. 10 Replies

IN addition to the main seal leak,,which i am going to tackle again tomorrow,i also have a leak in what seems to be the steering gear.  I have checked to connections from the pump, and its dry on…Continue

Blog Posts

driveshaft help

Posted by wayne weaver on October 9, 2019 at 4:41pm 1 Comment

can anyone help me with a driveshaft ? I have a 1963 Cadillac 62 series 4dr with the hydro-matic trans. I need the male splined shaft on the front of the rear driveshaft section. the piece with the nut attached by clip.id be willing to buy a shaft if its not horribly priced.

Dash removal

Posted by Jake Mickley on October 9, 2019 at 12:06am 9 Comments

Hello everyone,

On a 63 CDV, if a guy wanted to remove the entire dash to get all the metal painted, and do some other things behind there, how would he go about doing that?  I checked here and the shop manual, but can't find a complete guide.

As always, and help or direction is appreciated.  Thanks!

--Jake

Introducing myself

Posted by Gary Marchand on October 7, 2019 at 9:32pm 8 Comments

Thanks for letting me join the club.  Picked up this ‘64 Coupe Deville a few months ago out of Beverly MA, the car has few stickers on it from various Cadillac clubs, didn’t know if anyone might recognize it from it’s “Glory days.” Everything seems pretty healthy except for the body and some very Mickey Mouse repairs, was wondering if anyone had any leads on…

Continue

Carter AFB carburetor question

Posted by Ray Schick on October 7, 2019 at 8:29pm 8 Comments

3655S carb, and a 3656S carb .I know the difference is one is for A/C and the other in for a non A/C car . Now the question is : can I use the carb bowl from the A/C car on the non A/C car ? They look the same set up next to each other

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service