Does anyone have a decent pair of upper control arms to fit a 63? I'm not concerned about bushings, shafts, or ball joints as I had already planned on replacing them. Any help or leads are appreciated. Thanks!

-Nick

Views: 131

Reply to This

Replies to This Discussion

Hi Nick. I have at least 2 dozen sets and can sell you a set of good cores for $50.  Email me at jasonedge@nc.rr.com with shipping address for total and payment info.

I recently removed upper ball joints but didn't mark which side was which. Are the driver side and passenger side upper control arms interchangeable when the ball joint is removed?  They appear identical

According to my notes
"The lowers are the same left to right but according to master parts book left and right uppers are different. It says LH upper will have a daub of yellow paint on metal tag if original."
The core arms look the same to me, but to make sure I always mark the side when I remove from a parts car. Perhaps someone can confirm they can be swapped.

Thanks for the help! Unfortunately the arms were painted at some point, I do recall one side having a little ground strap attached to the arm bushing and one side didn't not sure if that would identify them...

There should be a ground strap on both and remember trying to use that as my guide but remember them being not consistent in terms of which end they were on.  If you have a picture inside the engine bay showing the upper control arms that show that ground strap that would confirm for you which side is which.

OK. So I looked at my upper control pictures on file and ALL have the ground strap on the rear. I checked the Shop Manual and MPB illustrations and they have the ground strap on the rear. I checked the very stock 1963 Parts Car I have outside and my own 64 CDV and both have ground straps on rear on both left and right side. So, if you still have the ground strap connected that will tell you which side as the ground should be on the rear. I think what I had seen maybe last year was a car where someone had just installed the ground on the front after some rework. You can install on front or rear, but I am now sure after some research they were on rear from factory.

Awesome! Thank you very much for your help Jason!

When I replaced the bushings and ball joints on my 63, I didn't see any difference in the bushing shaft or the control arm from the right or left side except for the ball joints themselves. Like Jason mentioned the ground strap was attached to the rear bushing retainer bolt on the right and left control arm.  In that end, I didn't bother keeping them marked when I pressed the old joints and bushings out but did keep aware of which one went right and left after the new ball joint was installed. I think when the cars were new, Cadillac replaced the control arm as an assembly therefore the factory marking Jason mentioned to identify the right from the left.

RSS

Photos

  • Add Photos
  • View All

Forum

Blog posts

Started by Anders in Suggestion Box. Last reply by Anders 7 hours ago. 4 Replies

Think I figured out why blog posts are still posted instead of the preferred discussion posts.My guess is that members go to their "My Page" and from there click the "Blog Posts" and then post a blog…Continue

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 12 hours ago. 169 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

MLK Day

Started by Chris Codd in General Discussion. Last reply by Kevin Campbell 21 hours ago. 1 Reply

A day late, but I saw a picture of MLK riding through Baltimore in a convertible and after a little research I found a different angle and saw that the car was a black '63 convertible so I had to…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

Road Trip

Posted by Ray Schick on January 21, 2020 at 9:00pm 4 Comments

Got a little cabin fever this morning,decided to take a road trip to Hickory Corners Michigan, The Gilmore Museum. It’s about 2 1/2 hours from my home . Place is awesome,I was really impressed.

9A648CFF-E965-4CE0-8E91-8E194AC70DED.jpeg…



Continue

1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…

Continue

Looking for the Rochester Choke Tube ...

Posted by Mack on January 10, 2020 at 1:14am 3 Comments

37E244B6-71C7-4857-8D50-1BD8C48077A4.jpeg

Looking to buy the choke tube for my Rochester... anybody have one for Sale???

AC/heater for 1964 Cadillac coupe de ville

Posted by Matias J. Adrogue on January 7, 2020 at 11:11am 9 Comments

Good morning!  I am Matias Adrogue.  I bought a 1964 Cadillac coupe de ville last year and am real close to the final restoration details!  I call her “Jaws 64”.  Pics will be posted soon.  I need advise regarding a AC/heater.  It came stock in the vehicle but it does not work.  A mechanic gave me a bid of $1700 to replace and repair.  I am ready to install a new system - Vintage Air or Old Air Products from Fort Worth Texas.  I would greatly appreciate your thoughts.  I read the great write…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service