Selling my 1964 Fleetwood. Car has 111K on it. I have had it three years. I don't think the engine has been opened up. It does have lifter noise when it sits for a few days, but quiets down when it warms up and the oil gets to the heads. The car runs good and the trans shifts smoothly. I have done mechanical and some electrical work to it. I have put about 400 miles on it since I've had it. Longest trip was about 30 miles, mostly city driving. The new, tires, shocks, brakes(shoes wheel cylinders hoses all new steel lines front to back master cylinder) exhaust(Kepich not very happy with the loud muffler and black resonator, they said they out source them, translation cheap junk) Floors have been patched with POR floor patch kit(previous owner put foam rubber under the rugs(enough said) new rug!  Pulled motor to replace exhaust manifolds. degreased and painted motor and engine compartment new oil pan, valve cover, exhaust manifold, intake manifold gaskets. rebuilt Carter carb all tune up parts, belts and hoses new front motor mounts. new heat riser(after market  already rusted) window wiring repaired (still needs work) I have a new door wiring harness and switch assembly for it (supplied by Jason) one vent window set of switches broken. I have installed new gears on all four vent window motoors and they work windows do not work at the doors just at the master. master window plastic clip loosens from switch occasionally (new harness will take care of that) Had to replace vacuum lines for door locks (they were cut out in kick panel) passenger door switch works, but not getting vacuum to one side of vacuum switch on driver side. six wat seat works, power antennae works, radio works, but if signal seek is pressed it blows fuse. A/C not hooked up cruise not hooked up not sure on light dimmer and sentinal. Only options missing are AM/FM radio, rear defrost, and controled differential. Body needs some work and paint. driver rear bumper end has holes (Ihave included a good one) Rust under vinyl top and the usual places. Car is Sierra Gold with Sandalwood vinyl yop and a full leather Sandalwood interior. seats were badly stained, could not get stains out, so I dyed the seats with the correct color. I have most of the receipts for the parts I bought, plus owner's manual, protection plan and build sheet info from Allied Vaughn. also a service manual and rug pieces to finish the center posts. This is a good project to finish. I have gone as far as I want to go on it, now the next custodian can finish. I think I've included most of the info on the, but if you have questions you can call me at 716 874 3223. I'm in Buffalo, NY I am going to try and include some pictures, but I'm not very computer literate so if they don"t come thru I can email them direct to you easier. Thanx Frank

Views: 625

Attachments:

Reply to This

Replies to This Discussion

Bumping this post up for Frank Puma who has dropped the price to $5500. See recent post at http://6364cadillac.ning.com/forum/topics/1964-fleetwood?xg_source=....

I still have the Fleetwood. Out of storage yesterday 5/5/18. Still for sale. Need the room. I have dropped the price to $4500. Contact info Frank Puma CLC #10721 7168743223 fpuma49@verizon.net. Thanx

SOLD

RSS

Photos

  • Add Photos
  • View All

Forum

1963 Ignition Bezel

Started by Lee Martin in 1963/64 Cadillac Specific Discussion 23 minutes ago. 0 Replies

Looking for a good ignition lock nut bezel for 1963!  This is the chrome piece that holds the ignition housing in place and protects painted dash from key scratches.  Opening must be more than 15/16"…Continue

Floor Pans

Started by Tommy Nicolosi in Restoration Discussion 56 minutes ago. 0 Replies

Are the floors on 1961-1964 the same???Continue

Back to Starter

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 1 hour ago. 39 Replies

Ok,  short refresher,  last dec i relpaced starter w rebuilt from usa parts.  and even then,  after short runs where i got up to temp, if i shutvcar off, and then tried to start, it would drag…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 3 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

HVAC Vacuum Valve Clip-need the one for the Power Control side

Posted by Norman Silverman on September 17, 2018 at 8:15pm 6 Comments

Hi.

Update:

I removed both 7 nipple vacuum valves and called my buddy who owns a machine shop. Tomorrow we'll re-surface the valve faces and then I'll reinstall them. HOWEVER, the one that comes out easily and comes apart with no rivet is on the Power module side. It installs on one side with a small bolt, and on the other it is held on by a clip, WHICH IS MISSING ON MY CAR. I am going to assume it is the same clip that is used on the Control Module side. Anybody got one? Happy…

Continue

7 vacuum valve-need a good one or someone to recondition mine

Posted by Norman Silverman on September 15, 2018 at 5:44pm 12 Comments

So, I've put my 7 vacuum valve from the control head side to the test, and it failed. I looked at the instructions for re-conditioning it and unless I am missing something, the instructions are missing something (about how to take off the clip that provides the tension that holds the two pieces together). 

In any case, I can't do this particular repair so I am looking for a new valve (not likely), or a good re-conditioned one, or someone who has done this before and would do mine for…

Continue

Mosiac Cadillac emblem Table

Posted by Dana G Cooper on August 30, 2018 at 10:48pm 11 Comments

Wanted to share a picture of a table my wife made for me to display with our 63 Coupe Deville. 

Inside door handle thread size

Posted by Michael Jarnagin on August 23, 2018 at 4:31pm 1 Comment

Anyone know the thread size on the inside door handle bolts mine are missing any info much appreciated 

Videos

  • Add Videos
  • View All

© 2018   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service