After renovating both the engine and the automat, I have vibrations. Not sure if they come from the engine or the transmission. Can the flexplate versus converter be wrong? or the flexplate against the crankshaft?

I`ve been wrenching Chevys since the sixties, so I´m not without experience. I guess I have the take the whole package out.

Any other suggestions?

Hoping for some smart solutions.

 Bo Authèn   Sweden.

 

Views: 48

Reply to This

Replies to This Discussion

Most likely the propellershaft. Bring the shaft to Sveabil in Bromma. They will balance and fix the CV-joints. Its not cheap but a lot cheaper than starting anywhere else. 

No, that`s not the problem, it`s been rebuilt already. I think I will take the transmission down and look for a broken flexplate or converter.

This happened to me after installing a replacement engine in a '64 Cadillac. I had a vibration once I had everything together and the car running. So I pulled the car up on ramps and took off the dust cover on the trans bell housing while the car was running. I could see clear as day where the vibration was coming from. Turned out the flex plate was bent. I swapped flex plates with the one from the bad engine and that did the trick. 


BO

Was your car on the road and driving with no  drivetrain vibration  before  the vibration showed up after the rebuild ?

If so that would eliminate the propeller shaft ( driveshaft ) from being any  issue now 

If the car is on the road for the first time —after this engine and trans rebuild the propeller shaft could be the vibration issue

Propeller shaft vibration is the most common drivetrain vibration issue on this site which comes up very often. ( much more on that  later if it is a possibility  ) 

Do check the flex plate -inside the inspection plate for out of round with )engine running as suggested here

Are all your engine and trans mounts new and fresh ( trans side  mounts adjusted correctly for a snug fit ) 

Did you change the  engines harmonic balancer for any reason ? 

Any vibration issue can be difficult to trouble shoot - I do feel your pain  with  this kind of issue 

Check out the things suggested on this thread and let us know if any help you out 

Enjoy 

Thank you for the answers, I will check all of the solutions and hopefully solve the problem.

Thank you, a great forum.

BO

Pls do let us know what it was  when you solve the vibration problem so many others can benefit from your quest 

Enjoy 

RSS

Photos

  • Add Photos
  • View All

Forum

Fuel gauge access

Started by Tosh Dickenson in 1963/64 Cadillac Specific Discussion. Last reply by Tosh Dickenson 3 hours ago. 2 Replies

Do I really have to remove the dash pad to access the back of the instrument panel..specifically the fuel gauge.  1964 DevilleContinue

Convertible Top Pump Leak

Started by Lee Martin in 1963/64 Cadillac Specific Discussion. Last reply by Lee Martin 9 hours ago. 5 Replies

Does anyone have experience with leaky pump or connections to pump?  I have a slow one and it's driving me crazy trying to see where the fluid is coming out.  It is definitely from the pump area (not…Continue

Fuel Gage

Started by Dominic Salemi in General Discussion. Last reply by Dominic Salemi 9 hours ago. 5 Replies

Any help on this 1964 Cadillac. My fuel gage is pegged over the full line. Is there a way I can tell without pulling everything apart to figure out if it is the gage or fuel unit. I disconnected the…Continue

ONLINE SERVICE MANUAL

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 15 hours ago. 2 Replies

I dont know if anyone has posted this, I stumbled on it and found most of the manual as a pdf.  kind of handy when i downloaded it onto the phone and am under car..anyway, here are the links that i…Continue

Blog Posts

63 Caddy Horn

Posted by Robert Alan Shannon on May 27, 2020 at 9:25am 10 Comments

 Just noticed a 1963  Caddy trumpet horn on Ebay. No part # given but some of his other items are 1963 specific, just throwin this out there, I have no connection to this listing .

Wiring connection help.

Posted by Jimmy Davis on May 24, 2020 at 9:15pm 2 Comments

Can someone help me figure where these connections go? I have a 64 60 special if it matters.…



Continue

Wood grain finally done.

Posted by Jimmy Davis on May 20, 2020 at 4:57pm 3 Comments

After years of wanting to, I finally redid my wood dash paneling on my 64 60s. Not too hard to do either.…

Continue

390 engine replacement needed

Posted by Jason on May 18, 2020 at 7:54pm 1 Comment

I’m looking for a 1963 Cadillac 390 engine that runs. 

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service