Hello, I have a 63 Cadillac Series 62 Convertible.

The car was recently rear-ended and I now have a dent in the rear bumper.
Separately, the front bumper has some rust holes.
I've attached pictures of both.
Can you advise what options I have for getting the dent out and fixing the holes, and potential pricing guesses?  I looked on the supplies page and sent an email to Bumperboyz, as I'm in Los Angeles, so we'll see what they say.  It may be cheaper to replace the front bumper ends than try to fix mine if I can find them.
Does anyone have good conditions parts for sale for either of these?
What would you do?
Thank you.
-Tim

1963-Caddy-Series-62-Convertible-Rear-Bumper.png

1963-Caddy-Series-62-Convertible-Front-Bumper.png

Views: 158

Reply to This

Replies to This Discussion

I got these prices from the local shop here in LA.

They would give me show quality pieces back, and take my cores in exchange.

Prices with acceptable core exchanges:

Rear center: $550

Rear ends: $320 x 2 ($640)

Front center upper: $250

Front center lower: $400

Front upper ends: $260 x 2 ($520)

Front lower ends: $350 x 2 ($700)

Total: $3,060 + any additional charges where the cores need to be patched and heavily repaired.

I am assuming they would not consider your smashed in rear center, and front lower ends "acceptable core exchanges".  With that I would ask for price without core.  I would just be clear on what the total might would more likely be. All of your prices are about in line with what would expect to rechrome good cores.. so no surprises there. 

RSS

Photos

  • Add Photos
  • View All

Forum

Rear Wheel Bearings Replacement

Started by Dominic Salemi in 1963/64 Cadillac Specific Discussion 9 minutes ago. 0 Replies

HiNeed to replace my rear wheel bearing and seal on my 1964 Conv., does anyone know if its a big project and what I will need before I pull the shaft out? I also need to know the parts number and…Continue

Winter time cruise in Australia.

Started by Kevin Campbell in General Discussion. Last reply by Kevin Campbell 14 minutes ago. 4 Replies

The weather here in winter is great for a Cadillac cruise.Continue

looking for a 429 heat riser and cruise control unit

Started by Christian Doerk in Wanted to Buy. Last reply by Kurt 1 hour ago. 1 Reply

I am looking for a functioning heat riser valve and a cruise control for a 1964 Cadillac.In principle, the heat riser flap does not have to work. It is only important that the spacer / housing is not…Continue

Tags: exhaust, riser, heat, control, cruise

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 2 hours ago. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

64 Power Servo vacuum leak

Posted by Kent Prows on June 27, 2020 at 4:02pm 0 Comments

I finally got around to fixing a leak in my heater core.  I decided to check to see if there were any other obvious issues while I had everything torn apart.  When I put a vacuum directly (bypassing the transducer) to the power servo it gets to about 10" and then slowly leaks back to zero.  The fan will not go to full and the mode door will not open completely.  I have read a couple of other posts that said they repaired the power servo leaks.  How?  Does anyone have one to sell?  I just…

Continue

63 Caddy Horn

Posted by Robert Alan Shannon on May 27, 2020 at 9:25am 9 Comments

 Just noticed a 1963  Caddy trumpet horn on Ebay. No part # given but some of his other items are 1963 specific, just throwin this out there, I have no connection to this listing .

Wiring connection help.

Posted by Jimmy Davis on May 24, 2020 at 9:15pm 2 Comments

Can someone help me figure where these connections go? I have a 64 60 special if it matters.…



Continue

Wood grain finally done.

Posted by Jimmy Davis on May 20, 2020 at 4:57pm 3 Comments

After years of wanting to, I finally redid my wood dash paneling on my 64 60s. Not too hard to do either.…

Continue

Events

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service