UPDATED/shortened: 5/8/2019 11:59AM

Hello,

My 63 series-62 started and ran great up until about 9 months ago.  I was cranking it as usual, and on maybe the 4th attempt, all the sudden it went completely silent. Not a single noise when attempting to crank, no sign of life whatsoever.

Turns out, the cause of this was the Neutral Safety Switch.  I jumped the purple and blue NSS wires together, and then I was able to start the car and get it running!

Thanks!

Part 2. I ordered a new cranking harness from Jason, because in diagnosing, I noticed mine was melted behind the ignition switch. I had questions about where each part of the harness connects to.

I have the shop manual, and I look at the starting circuit diagram, and for the most part it makes sense, I just wish they included the color and gauge of each wire in the diagram, that would make things so much easier.

Then, Anders pointed me to a giant color coded wiring diagram which I've just ordered, and that should get me going: https://www.classiccarwiring.com/1963-cadillac-color-wiring-diagram/

Thanks for the help, much appreciated.

Now I just need to find or figure out how to repair the NSS.

-Tim

Views: 98

Reply to This

Replies to This Discussion

3 years ago I bought a wiring diagram (the largest version). I'm very satisfied with it.

The supplier is listed on our "Parts Suppliers" list.

Here is a direct link for your car:

https://www.classiccarwiring.com/1963-cadillac-color-wiring-diagram/

Thanks, that is awesome, original factory wire colors! I am ordering this now.

Check the NSS to see if it is letting 12V go through it to the starter.  You can always jump the 2 wires together, but that disables the safety feature.

Anders 

That wiring diagram is a very nice thing to have 

Enjoy 

Anybody know of something similar for a vacuum diagram? That'd also be nice.

Should be in the help tab up top.

RSS

Photos

  • Add Photos
  • View All

Forum

Intake manifold gasket leak

Started by Joe DiIaconi in Restoration Discussion. Last reply by Tony and Ginny 429 8 hours ago. 1 Reply

Hello Cat's & Kitten's :) Happy Turkey Day ! I believe I have an intake manifold leak. The last time I bought an intake manifold gasket with the chock port blocked from Olson's gasket's. This…Continue

Happy Thanksgiving to all of our 1963/64 Cadillac Chapter & Website Members!

Started by Jason Edge in General Discussion. Last reply by Tony and Ginny 429 14 hours ago. 3 Replies

Earlier Fall Picture with 'Dino'I just wanted to wish all of our US…Continue

Tags: Thanksgiving, Happy

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 19 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Dipstick tube

Started by JOHN V SCHILLACI in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 3 Replies

Hello, Does anyone know off hand if the dipstick tube can be changed without the removal of the oil pan?  It's a 1964 Cadillac De Ville ConvertibleContinue

Blog Posts

Picture of ignition switch

Posted by Cees de Bunje on November 27, 2020 at 6:20am 0 Comments

Does anyone have a close-up picture of the ignitionswitch with keys in it made in landscape format? Switch must be in dashboard. Many thanks in advance. Cees.

1964 Cadillac Fleetwood sixty special / transmission dipstick needed

Posted by Pablo on September 20, 2020 at 9:57pm 1 Comment

How are you doing folks, I’m looking for a transmission dipstick, any info I will appreciated, thank you very much

1963 Cadillac hood driver side hinge

Posted by Steven on September 16, 2020 at 9:23am 1 Comment

Hello,

 Does anyone know were I can buy a 1963 Cadillac hood driver side hinge or is there any other hinge that would fit? 

Thanks

Steven

Bad Guage?

Posted by Karl Schwarz on August 26, 2020 at 3:08pm 6 Comments

So I am troubleshooting my fuel gauge issue. I bought a new sender and tested it. It  it goes from 1-ohm (empty) to 35-ohm (full). When I test it (outside the tank), when the float is in the up (full) position it only moves the gauge to about 1/2 full. When at the bottom (empty) position the gauge shows empty. This is the same issue I have when I fill and then use the gas in the tank - the gauge never reads ore than half full. Based on what I've read on this thread it would seem like the…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service