We are reconstructing the front split seat, with armrest, for our 64 convertible. We are starting with the metal frame/springs. Anyone have photos/details on the foam /cushion material to get a good shape etc as the base for the new upholstery? Also reconstructing the rear seats as well so any info for them would be helpful as well.

We have the actual finish upholstery being made now.

Thx

Views: 212

Reply to This

Replies to This Discussion

Sorry i can't help much Tom. I had my seat redone by a shop. They had to rebuild my foam and burlap also. It turned out very good but if I had the car longer before getting it done I would have looked into doing more with the springs or cushions. They are not the best for long distance driving. When I service my seat tracks and power seat mechanism I will probably look at the support then. There is some excellent posts in the help section regrading servicing the power seat mechanism. 

Thanks, Will check out the posts for the mechanisms when we get there. Ours is a 6 way power mechanism  that had been set up with NON center armrest front seat. Will be moving that 6 way  base setup to under the correct front seat, with the center armrest, I now have to use.

Would like to transfer 6 way seat control to the door panel as i already have a door panel with the 6 way switch mechanism . Do you know if there is a separate wiring harness that runs from the door mechanism to the front seat? or will i find the wires there when we get the door panel off the door?

You may find the wiring harness from the door panel under the seat. Get down there and have a look around with a flashlight. If the seat without the arm rest was controlled by a switch on the seat then all they would have had to do was run a power wire to it. Your wiring harness from the door wouldn't have supplied any power so they would need to run a separate line. The old plug may just be laying on the floor and you can reconnect it and use door controls. Hoping for that anyways lol.

Rereading your post do you have a door seat switch currently installed? Or a spare one you want to install? Does the new seat have a switch on it?

Clovis,

The seat 6 way seat switch mechanism is currently installed on the left side of the INCORRECT seat . I will be reusing the 6 way track/motor etc mechanism under a correct seat with the armrest.

The existing door panel does NOT have a seat control switch- it only controls the windows. BUT-this car was originally made with the 6 way seat option.

  So I have two options to consider, do I set this up with the 6 way controls on the door (I have a 6 way switch I could use there) Or leave it in the side of the seat?

The new(replacing) seat does NOT have a switch on it so we can go either way

From the factory the 1964 convertible, both the 6267 de Ville Convertible, and 6367 Eldorado Convertible, would have had the power seat switch in the arm rest switch panel.
Just fyi, from the factory the 1964 Series 62 Coupe and Sedans, had the seat switch on the seat bottom left metal trim.  The door panels and switch setup on the Series 62 was completely different from the deVilles, using small isolated switch pods mounted to the door pane for the window switch in front of the short isolated arm rest behind the door release handle.  
From the last reply it sounds like you have the original door panels and arm switch panel and a 6 way seat switch to go back in the switch panel? If that is the case it would be a no brainer... seat switch from the the door arm rest control as it was from the factory. If you no longer have the correct 2 piece deVille power seat harness, I do have as indicated. 

JASON,

Outstanding.-- In that case I will definitely set this car up with the 6 way seat controlled from the door panel switch setup-- now to see what is left in the car and if I need the harness and/or the lower seat trim -solid  I know you have them.

PS. Just for your info, whoever setup this Scarface version used that series 62  setup probably from a 1963 coupe and welded one to the door itself !

 

Tom, The power seat wiring harness on deVilles/Fleetwoods is a 2 piece harness and is very different from the one piece Series 62 lower seat trim mounted seat switches.  It runs from the arm rest switch plate, thru the door to body rubber conduit, down behind the driver kick panel, into a thick rigid plastic body feed conduit under the door seal plate, T's off toward the seat toward front of seat, runs under carpet and tot he seat. On the Series 62 seats you only have power running over to the seat harness, as the harness itself is one piece and confined to LH side of the seat from switch in lower left metal bench seat trim, to relay, motor and transmission.  

I have the  deville/Fleetwood style 2 piece door wiring harness in very nice condition, no breaks in the wiring (which are common as it goes through the door grommet) for $35 and can ship 2 to 3 day Priority in USA for $7 for a total of $42.  If interested email me at jasonedge@nc.rr.com.
Below is a picture of the complete 2 piece harness. Ignore the circle around the connector! I'm sure I was pointing something out to someone and forgot to save the source pic.

Jason, Sending you an email for those harness' Got the front seat out of our 64 SATURDAY  and I see what you mean!

thx

You can see pictures of the bottom of my bench seat in my 64 CDV in my Interior Project thread by Clicking Here then scrolling down a bit.

On my 64 convertible the wires run under the carpet to a power source just under the right side of the drivers seat at the front
The power switch is on the door at the front of the control pannel
Not sure if the wires come from under the entrance kick plate or from under the carpeted kick plate on the drivers side

Very often these motors can be cleaned of old hard gease and regreased to work again

Enjoy

I'm almost certain they run under the drivers sill plate. There is a channel under there for wiring.

RSS

Photos

  • Add Photos
  • View All

Forum

Is this possible or total BS?

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 5 hours ago. 5 Replies

After changing tie rods, i tokk car into wheel n allignment shop. He said no problem.  He calls back about 45 minutes later and said they couldnt get between the tire and cowl, the guys head was too…Continue

Vacuum / Parking Brake / NSS Question

Started by Karl Schwarz in 1963/64 Cadillac Specific Discussion. Last reply by Karl Schwarz 6 hours ago. 2 Replies

I bought a 1963 Series 62 Convertible in July.It makes a hissing sound when in neutral, and sometimes when in drive (when the shift is more to the left that the right. I assume this related to a NSS…Continue

Tail pipe black stuff!

Started by Lambert Ross in 1963/64 Cadillac Specific Discussion. Last reply by Lambert Ross yesterday. 10 Replies

any ideas how to clear the ugly black stuff shooting out from my tailpipe? After a long layover, it really messes up the garage floor. I assume its carbon but am not sure how best to react to it.…Continue

Blog Posts

still need a driveshaft

Posted by wayne weaver on November 26, 2019 at 11:53am 0 Comments

well thank you UPS for losing the driveshaft that Russ Austin shipped me. 

however i still need a rear driveshaft section for my 63. mine has a vibration due to the bushing inside of it. its a shame because the ball and sockets in the cardian joints are perfect but it has a woble on the balancing machine. so .  still need the rear section. anyone have a good one ? is there driveshaft alternatives to use ? i am really considering an LS swap and since im fighting the driveshaft search…

Continue

63 guidematic issues

Posted by maurice lapoiinte on November 24, 2019 at 3:10pm 0 Comments

 So my 63 guide matic headlamps stay on low beam all the time. I have so far bypassed the system and everything works normal. I have been thru the trouble shooting in the manual but this is where the confusion begins.on my car when the power relay is powered I have low beam and when its not powered I have highbeam, this appears to be opposite what the diagnosis says should be correct.The wiring is all original and no wires have been mixed up.has anyone ever unplugged the 2 wire connector…

Continue

Another advantage of the Pertronix III

Posted by Doug Scarrow on November 23, 2019 at 11:12am 1 Comment

   Having tried both the II and III I can say the multispark feature of the III offers a smoother idle . It is also easier to install .Does not require removal of the distributor

Stuck at two red (dash) lights!

Posted by Jeff Kinzler on November 3, 2019 at 10:00pm 9 Comments

I hope someone can help solve these two electrical problems that appeared one after the other.

By way of background: The car, a '64 Eldorado has very limited use. It was at a restoration shop for 15 months until last January-  that supposedly did a bunch of wiring repairs including rebuilding the gas gauge that still hasn't worked properly, and the clock that hasn't worked, and re-soldering the broken wires in the drive door. All window and seat controls appear to be…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service