My driver side tail light does not work. The lights on the fin works, passenger side works. Check the fuses everything looks good. Should I follow the wire from the tail light and where does it run to. Is it in the trunk or underneath the car. Thanks

Views: 150

Reply to This

Replies to This Discussion

Testing the tail light is made easy since the connector is just inside the license tag/gas door on the back trunk wall. Looking at pictures below, just flip the gas door down, reach over and unplug the connector on the left at back trunk wall, and apply 12 volts to each of the 3 connector.
- Light Green control backup light
- Purple  controls brake and turn signal
- Dark Green controls tail light/park light and license plate light.

Check each one to see if they are working if 12 volts is applied. If they all work your problem is in front of the connector. If one doesn't work, the bulb might be burned out, you might have a grounding issue, or the socket is not making good contact.

Access to the tail light bulbs requires removing the center tail lamp center ornament bar (3 sets of 2 screws), then the tall clear tail light lens via top and bottom screw and then gently prying the lens away from the gasket and removing/checking the bulbs. Sometimes the spring that pushes the contact up toward the bulb base tip gets corroded and you can work it back and forth with needle nose pliers and WD40. Sometimes they base of the fixture loses contact with the tail light fixture. You can usually take punch and notch up against the rim to make ground contact again. If all else fails there are push in spring type replacement lights bulbs in the "Help" section of most auto stores. This requires removing the tail light fixture, and prying the lip off the old bulb so that you can remove it. Hopefully you just have a burned out bulb, or the spring isn't making contact and can be fixed.

Just one other note, I have used a heater hose... I think maybe 3/4" hose to push onto the bulb to be able to push in and turn out. The back up light in particular is hard to reach in and get your hand on.

Here are the pictures of testing the tail lights from the back wall connector. I am using a simple 1amp 12 volt AC/DC adaptor with alligator clips, however you can use any 12 volt DC source.

Flip door down and see connector over the left and unplug:


Here is a close up with connector unplugged:


I am simply using a 12 volt AC/DC adaptor with pointed tip alligator clips. Negative is on Ground and Positive is attached to each contact testing each light.

Observe the lights as you test. Here I have the 12 volts on the light green wire for the back up lights.

Wow thanks for the great detail. I will trouble shoot everything this after noon

I use folded aluminum foil to fill the gap between the fixture and the bulbs base so contact is made after the WD -40 to work the spring
For any side to side movement a toothpick and a dab of crazy glue will stabilize the bulb
Prevents bumps from jiggling the bulb loose

Living in Florida for 13 years you pick up some inovative Red Neck Tricks

If you have to move your transmission to take a bath -- you could be --a Red Neck ---LOL !!!!!

Enjoy

Jason

Real nice extremely detailed taillight electrical repair info
A lot of variables going on there
Electrical issues can be challenging
Nailed the subject
I took some notes as i often do
I have an accordian file of all detail notes from the Cadillac websites i have collected since 2006
Just always enjoying knowing all i can about the 64 Cadillac

Enjoy

Clean all conections to shinny metal

The wiring going into the plug can be removed ( backed out ) from the plug by slipping a small flat tool into the socket
Removing the wire from the plug will help you access the terminal to clean to well
They sell a spray to clean plug in terminals
I always clean them by hand myself

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

Steering Wheel

Started by Mark Borer in General Discussion 3 hours ago. 0 Replies

plz watch this videoIt shows play between the 2 cylinders that make up my columni have tightened everything up as best as I can....but it moves a bitthe lower cover had a screw that lined it up, and…Continue

Exhaust manifold: Repair, replace or headers?

Started by Dutch Dickinsen in General Discussion 3 hours ago. 0 Replies

My newly acquired '64 Coupe DeVille suffers from a cracked right side exhaust manifold.It looks like my options are limited to rolling the dice on a used manifold, converting to headers or seeing if…Continue

Tags: 429, manifold, exhaust

Help! I need a 1964 Eldorado front left fender.

Started by Jorge M in Wanted to Buy. Last reply by Jon Ettman 5 hours ago. 5 Replies

Help looking for a 1964 Eldorado front fender for a convertible.Thank you please contact djjmoreno84@gmail.comContinue

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 157 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…

Continue

Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.

Thanks

Dominic

Upper A Arm Rubber Bumpers

Posted by Gene McIlroy on August 12, 2019 at 1:30pm 3 Comments

I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.…

Continue

Roof motor

Posted by Dermot Robinson on August 11, 2019 at 8:44am 2 Comments

Replacing my convertible roof motor.

Has anyone any experience or advice on replacing the roof motor on a 1964 Cadillac Deville .

Please..

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service