Does anyone else have trouble getting their finger between the grill slats and moving the hood release lever enough to pop the hood?  I almost need to make some sort of special tool to help with this operation.

Jim

Views: 175

Reply to This

Replies to This Discussion

Should not have to go between slats to get to release lever, it should be accessible by reaching under the painted center bar of the grill. Lever has some adjustment, also your upper grill section has some adjustment and it may need to be adjusted upwards to allow your hand to get under the center bar to reach release lever.

Like Ronnie said, under the center grill bar.

As the great philosopher Homer said...... dooooh!! That would be Homer Simpson 

You did not understand my question.  I KNOW how to open my hood!  The space below the center painted bar is small and I can only get the tip of my finger through and trying to open the hood using the lever with the tip of my finger is almost impossible.  I can insert my finger up to the knuckle in all other slats.  I need to widen the space where the lever is

I assumed you knew how to open your hood. The pictures I posted show the correct alignment of the grill and WHERE to stick your finger into the grill.  If you take the time to look at the second picture I posted, you will see the overlap of the top grill to the bottom grill. 

You asked for help, I took time out of my day to take a few pictures and post them for you.  I suggest you use bit more sugar in your replies when you ask for help.

Russ,

I apologize to you.  My comment was aimed at Clovis's remark.  I appreciate your response and the photos are very helpful, especially the one from the inside.  You and Jason have helped me in the past and I appreciate the wealth of knowledge you share with the group.  Again, my comment was not intended to be directed to you.  Once again, sincere apologies!

Jim

The grills often become misaligned leaving little room to get the fingers in there. The upper grill should extend far enough past the lower grill to reach up and over to access the lever. If either grill has been moved, replaced, bent, or anything to move from factory set-up it can be difficult to have access. There are many connection points on upper and lower grill, I would look at upper grill and see if you can loose and move forward a tad.  The lower grill may have also been previously installed too far forward. With everything loosened up, there is some play in upper and lower grills. This is one of those items were if either were just reinstalled without consideration to the overlap of the upper to lower grill to provide access to the lever (not to mention stock look) this is one of those things where you almost always end up going back up and making more adjustments. Mine is on the tight side since my last lower grill install and need to make some tweaks.

Thank you Jason.  Yes, the front grill has been worked on.  I'll show your response to my body guy and have him figure it out.  Thanks again!

Jim I didn't mean to offend you. I've owned my 64 for 4 years now and still have to "remember" how to open the hood. As I call it my doooh! moment. Probably age has something to do with it or to many cars to remember what opens what way. Keep on smiling!

One thing about the old car hobby it keeps us on our toes at times. 

RSS

Photos

  • Add Photos
  • View All

Forum

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 3 minutes ago. 10 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

1963 Chateau deVille?

Started by thejollychimp in 1963/64 Cadillac Specific Discussion. Last reply by Richard Otto 16 hours ago. 3 Replies

Have any of you seen or heard of a "Chateau deVille" model? I searched the internet and only found two references to it (below). Sounds like it might have been a dealer installed package? I actually…Continue

Custom '64 Eldorado on Bitchin' Rides Last Night

Started by Ian Osborne in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

If anyone here is familiar with the show "Bitchin' Rides" they started work on a '64 Eldo on the episode that aired last night (12/5). I really like the show and they build some amazing custom…Continue

Blog Posts

still need a driveshaft

Posted by wayne weaver on November 26, 2019 at 11:53am 0 Comments

well thank you UPS for losing the driveshaft that Russ Austin shipped me. 

however i still need a rear driveshaft section for my 63. mine has a vibration due to the bushing inside of it. its a shame because the ball and sockets in the cardian joints are perfect but it has a woble on the balancing machine. so .  still need the rear section. anyone have a good one ? is there driveshaft alternatives to use ? i am really considering an LS swap and since im fighting the driveshaft search…

Continue

63 guidematic issues

Posted by maurice lapoiinte on November 24, 2019 at 3:10pm 0 Comments

 So my 63 guide matic headlamps stay on low beam all the time. I have so far bypassed the system and everything works normal. I have been thru the trouble shooting in the manual but this is where the confusion begins.on my car when the power relay is powered I have low beam and when its not powered I have highbeam, this appears to be opposite what the diagnosis says should be correct.The wiring is all original and no wires have been mixed up.has anyone ever unplugged the 2 wire connector…

Continue

Another advantage of the Pertronix III

Posted by Doug Scarrow on November 23, 2019 at 11:12am 1 Comment

   Having tried both the II and III I can say the multispark feature of the III offers a smoother idle . It is also easier to install .Does not require removal of the distributor

Stuck at two red (dash) lights!

Posted by Jeff Kinzler on November 3, 2019 at 10:00pm 9 Comments

I hope someone can help solve these two electrical problems that appeared one after the other.

By way of background: The car, a '64 Eldorado has very limited use. It was at a restoration shop for 15 months until last January-  that supposedly did a bunch of wiring repairs including rebuilding the gas gauge that still hasn't worked properly, and the clock that hasn't worked, and re-soldering the broken wires in the drive door. All window and seat controls appear to be…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service