Does anyone else have trouble getting their finger between the grill slats and moving the hood release lever enough to pop the hood?  I almost need to make some sort of special tool to help with this operation.


Views: 185

Reply to This

Replies to This Discussion

Should not have to go between slats to get to release lever, it should be accessible by reaching under the painted center bar of the grill. Lever has some adjustment, also your upper grill section has some adjustment and it may need to be adjusted upwards to allow your hand to get under the center bar to reach release lever.

Like Ronnie said, under the center grill bar.

As the great philosopher Homer said...... dooooh!! That would be Homer Simpson 

You did not understand my question.  I KNOW how to open my hood!  The space below the center painted bar is small and I can only get the tip of my finger through and trying to open the hood using the lever with the tip of my finger is almost impossible.  I can insert my finger up to the knuckle in all other slats.  I need to widen the space where the lever is

I assumed you knew how to open your hood. The pictures I posted show the correct alignment of the grill and WHERE to stick your finger into the grill.  If you take the time to look at the second picture I posted, you will see the overlap of the top grill to the bottom grill. 

You asked for help, I took time out of my day to take a few pictures and post them for you.  I suggest you use bit more sugar in your replies when you ask for help.


I apologize to you.  My comment was aimed at Clovis's remark.  I appreciate your response and the photos are very helpful, especially the one from the inside.  You and Jason have helped me in the past and I appreciate the wealth of knowledge you share with the group.  Again, my comment was not intended to be directed to you.  Once again, sincere apologies!


The grills often become misaligned leaving little room to get the fingers in there. The upper grill should extend far enough past the lower grill to reach up and over to access the lever. If either grill has been moved, replaced, bent, or anything to move from factory set-up it can be difficult to have access. There are many connection points on upper and lower grill, I would look at upper grill and see if you can loose and move forward a tad.  The lower grill may have also been previously installed too far forward. With everything loosened up, there is some play in upper and lower grills. This is one of those items were if either were just reinstalled without consideration to the overlap of the upper to lower grill to provide access to the lever (not to mention stock look) this is one of those things where you almost always end up going back up and making more adjustments. Mine is on the tight side since my last lower grill install and need to make some tweaks.

Thank you Jason.  Yes, the front grill has been worked on.  I'll show your response to my body guy and have him figure it out.  Thanks again!

Jim I didn't mean to offend you. I've owned my 64 for 4 years now and still have to "remember" how to open the hood. As I call it my doooh! moment. Probably age has something to do with it or to many cars to remember what opens what way. Keep on smiling!

One thing about the old car hobby it keeps us on our toes at times. 



  • Add Photos
  • View All


Limo rear A/C box needed

Started by Anthony McCarn in Wanted to Buy. Last reply by Jason Edge 11 hours ago. 4 Replies

the case of my rear evaporator box was severely damaged by the p/o of my car. just in need of the case, but will buy a whole unit if the price is right. thanks!Continue

Tags: box, evaporator, conditioning, air, a/c

looking for a seat belt protector

Started by Christian Doerk in Wanted to Buy. Last reply by Jason Edge 11 hours ago. 5 Replies

I'm looking for a seatbelt protector (marked red) for my Fleetwood Sixty Special (6039) for the CENTER seatbelt. Not the driver or passenger seat belt protector. It's a chromed plastic piece.…Continue

Tags: belt, seat

63 390 engine block needed

Started by Pete Grodem in Wanted to Buy. Last reply by Russ Austin 12 hours ago. 1 Reply

Hellolooking for a good 63 390 block, standard bore preferred.thank youPeteContinue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 19 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…


Road Trip

Posted by Ray Schick on January 21, 2020 at 9:00pm 7 Comments

Got a little cabin fever this morning,decided to take a road trip to Hickory Corners Michigan, The Gilmore Museum. It’s about 2 1/2 hours from my home . Place is awesome,I was really impressed.



1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…


Looking for the Rochester Choke Tube ...

Posted by Mack on January 10, 2020 at 1:14am 3 Comments


Looking to buy the choke tube for my Rochester... anybody have one for Sale???


  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service