Hi,
I have a question regarding my AC, I recently had all new ac equipment installed and when I turn the ac on it only blows from the floor not the ac vents, my mechanic is having trouble trying to figure out how to get it to blow from the vents, any ideas?

Views: 109

Reply to This

Replies to This Discussion

Check out my post regarding comfort control systems. I just went through mine and posted it all there. I am assuming that you have a '64 with comfort control. It's all vacuum related.
I just checked out your car and it a '63. So my post isn't going to be fully helpful. It sounds like your mode doors are not moving according to where you set your controls. This is always vacuum leak related. You may need to check all lines and door actuators for vacuum leaks. Check all one way valves for leaks also. I'm not familiar with the 63 but your system would be simpler than the 64 so you should have an easier time chasing down your leaks. The only other thing is if your modes are cable operated then one of the cables have broken loose or something on that vein. Check the holy grail (shop manual) to see where to start with vacuums. Good luck as these are much more enjoyable on the hot days with air.
Thanks Clovis I appreciate your help.

RSS

Photos

  • Add Photos
  • View All

Forum

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 1 hour ago. 161 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

NOTHING IN MOTORING COULD PLEASE HER MORE!

Started by Jason Edge in Chapter Discussion 3 hours ago. 0 Replies

Ok.. How about one more scan for today from the 1964 Cadillac Mailer I will be including in an upcoming newsletter.…Continue

Discover a New Measure of Automobile Pleasure!

Started by Jason Edge in Chapter Discussion. Last reply by Tony and Ginny 429 6 hours ago. 1 Reply

OK. I'm having fun with this mailer I have scanned in. Cadillac sure had a way with describing their cars back in the day! Here is the back cover of the 6 page mailer you will seen in an upcoming…Continue

Blog Posts

Starter Solenoid replacement-how difficult? Where to buy?

Posted by Norman Silverman on August 20, 2019 at 8:24pm 8 Comments

Hello All.

I believe the starter solenoid has gone bad in my 64 DeVille. When I turn the key, often all I get is a click, then if I try a few times again the starter turns perfectly. All battery cables are on tight and the battery is good. So, I believe this problem is the solenoid. Where do I buy the right solenoid and is it necessary to remove the starter in order to swap it out? …

Continue

Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…

Continue

Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.

Thanks

Dominic

Upper A Arm Rubber Bumpers

Posted by Gene McIlroy on August 12, 2019 at 1:30pm 3 Comments

I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service