Back to redoing the interior on our 1964 Deville convertible. Have the front door panels pretty close to replacement with new vinyl etc. Does anyone have a diagram . or explain how the chrome control panel, especially the vertical chrome piece at the lift handle, is assembled to the interior door panel. The front screw is obvious, the rest is not to me.

Also, what is the screw size that hold the lift handle on.

Thanks

Tom

Views: 103

Reply to This

Replies to This Discussion

The rear of the arm rest switch plate screws into the large right angle metal bracket that is attached to the side of the door as seen below. There is a long slot in the middle for the plastic piece of the arm rest to screw into, and a hole near the rear as seen in this picture for the rear of the switch plate. Note that the front arm rest chrome handle cover goes on first, then the arm rest switch plate, and the finish screw goes down through both.

The door release handle screws as a 10-24 thread, is about 1/2" long, with a 5/16" hex head and an external star washer under the head. I have plenty if you need one.

Jason,

Yes , Those metal brackets are missing from each door of our car.  Do you have a set of those brackets?

 

Tom, Yes I have plenty. Let's say $5 each bracket including the large short attaching screws for a total of $10 + $7 s/h for a total of $17. If you need any of those small door release handle screws just add 1$ each. You can shoot me a PayPal to jasonedge@nc.rr.com or you can email me for further discussion or if I need to send you an invoice.

Sounds fine, Do you also have the two(four) screws that will hold the two chrome pieces to the door bracket?

yes, I have the 4 chrome arm rest switch plate finish screws. Just add another buck.

Thx, Jason knew something was missing from each door--you solved it.

Paid youvia paypal already.

Tom

PS. Till the next missing part!

Everything will go out in the morning. Glad to help and thanks for the business.

Jason, Near each end of the door pulls I am missing a screw that I believe would fasten the pull to the inside edge of the door panel.

 If you can tell me what size they should be or include four I would appreciate it.

Thanks for your help once again.

Tom

I can throw in 4 of those large screws.

RSS

Photos

  • Add Photos
  • View All

Forum

Turn signal

Started by Jeroen Welgemoed in 1963/64 Cadillac Specific Discussion. Last reply by Jeroen Welgemoed 3 hours ago. 4 Replies

Hi all. It has been a while since i last asked or posted something. My car has his engine put back in and i am now just working om some loose ends.The last thing i have to do before i can get on the…Continue

New transmission mounts for sale.

Started by Russ Austin in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 13 hours ago. 1 Reply

I have 3 new transmission mounts for the 64 Turbo Hydromatic.  New from Steelerubber, still in the bag. I took one out to take a picture.These retail for 127.40  but you can get them from me for…Continue

63 jetaway transmission

Started by Scott L Foltz in Restoration Discussion. Last reply by Russ Austin 17 hours ago. 4 Replies

Hello and thank you for letting me join this group. While I was driving my 63 model 62 my trans cooler line blew off and needless to say I ran out of fluid. The next day I replaced the rubber hose…Continue

Tags: Transmission

CLC 2019 Grand National - Louisville, Kentucky, June 11-15, 2019

Started by Jason Edge in General Discussion. Last reply by Marty Smith 23 hours ago. 35 Replies

1963/64 Cadillac Chapter 2019 Grand National Page www.2019GN.6364Cadillac.com…Continue

Tags: National, Grand, CLC, 2019

Blog Posts

Cadillac Returns to its Roots Under New Leadership

Posted by Jeff Kinzler on May 1, 2019 at 12:30am 3 Comments

Cadillac’s new boss says they should stop trying to build BMWs and go back to building Cadillacs again.

What do you think? 

https://carbuzz.com/news/cadillac-finally-admits-what-everyone-knew-for-years

Radiator And Shrouds

Posted by Dominic Salemi on April 24, 2019 at 3:36pm 1 Comment

Hello

Anyone have a decent radiator and shrouds and hardware for a 1964 Cadillac deville. I have an alum. radiator and I'm deciding on to fix it or back to the original one. If I fix it I won't need parts.

Thanks

64 Recirc/Fresh Air Door Actuator replaced; FROM THE INSIDE.

Posted by Norman Silverman on February 4, 2019 at 11:21pm 8 Comments

I am happy to report that I have successfully replaced the Fresh Air/Recirc door actuator that is located on the blower box-and have done so without having to remove the blower box. I did it by taking out the glove box and attacking it from the back.  It took several days, LOTS of patience and some band-aids, but it is done. THE most difficult part -BY FAR- is to remove and then replace the screw that sits on the actuator arm, connecting it to the fresh…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service