Back to redoing the interior on our 1964 Deville convertible. Have the front door panels pretty close to replacement with new vinyl etc. Does anyone have a diagram . or explain how the chrome control panel, especially the vertical chrome piece at the lift handle, is assembled to the interior door panel. The front screw is obvious, the rest is not to me.

Also, what is the screw size that hold the lift handle on.

Thanks

Tom

Views: 76

Reply to This

Replies to This Discussion

The rear of the arm rest switch plate screws into the large right angle metal bracket that is attached to the side of the door as seen below. There is a long slot in the middle for the plastic piece of the arm rest to screw into, and a hole near the rear as seen in this picture for the rear of the switch plate. Note that the front arm rest chrome handle cover goes on first, then the arm rest switch plate, and the finish screw goes down through both.

The door release handle screws as a 10-24 thread, is about 1/2" long, with a 5/16" hex head and an external star washer under the head. I have plenty if you need one.

Jason,

Yes , Those metal brackets are missing from each door of our car.  Do you have a set of those brackets?

 

Tom, Yes I have plenty. Let's say $5 each bracket including the large short attaching screws for a total of $10 + $7 s/h for a total of $17. If you need any of those small door release handle screws just add 1$ each. You can shoot me a PayPal to jasonedge@nc.rr.com or you can email me for further discussion or if I need to send you an invoice.

Sounds fine, Do you also have the two(four) screws that will hold the two chrome pieces to the door bracket?

yes, I have the 4 chrome arm rest switch plate finish screws. Just add another buck.

Thx, Jason knew something was missing from each door--you solved it.

Paid youvia paypal already.

Tom

PS. Till the next missing part!

Everything will go out in the morning. Glad to help and thanks for the business.

Jason, Near each end of the door pulls I am missing a screw that I believe would fasten the pull to the inside edge of the door panel.

 If you can tell me what size they should be or include four I would appreciate it.

Thanks for your help once again.

Tom

I can throw in 4 of those large screws.

RSS

Photos

  • Add Photos
  • View All

Forum

Photo posting appears to be broken

Started by Kevin Campbell in General Discussion. Last reply by Kevin Campbell 2 hours ago. 9 Replies

Hey Jason,It would seem, the photo posting bit could do with a tickle on the bottom to get some action happening. I understand, you're probably still making like a friggin gopher in one of your…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 3 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Where to get brake booster and master cylinder rebuilt

Started by Chris Gill in 1963/64 Cadillac Specific Discussion. Last reply by Chris Gill 4 hours ago. 5 Replies

Hi folks,I'm new to Cadillacs so bear with me if this question has already been answered but I did a search of the forum and couldn't find an answer.It appears I have an original master cylinder…Continue

1964 Cadillac Coupe for sale

Started by Hank Johnston in For Sale. Last reply by Hank Johnston 5 hours ago. 8 Replies

Hi fellas, regretfully I am trying to sell my 1964 Cadillac Coupe deville. I've had it almost 4 years now and am having to face facts that I just dont have the time or money to do what I want with…Continue

Blog Posts

Flashers

Posted by Mike Petrey on January 13, 2019 at 12:25pm 7 Comments

Where do the flashers go in my 64 Deville Convert.  I'm thinking that's why both turn signals stopped working.

Source for Motor mounts and Trans mounts 1964 SDV

Posted by Norman Silverman on January 9, 2019 at 4:23pm 2 Comments

Hi.

Where is the best place to purchase good quality motor mounts/trans mounts for my 1964 SDV? I see that Rock Auto has them for $8 and change, and others for $24 and change. Big difference. Is there a better place to buy them from?

Thanks

Norm

Fuel loss in Carburetor

Posted by Ian Osborne on December 29, 2018 at 11:24pm 16 Comments

Lately if I haven't started my '63 in four or five days it seems that the carburetor has gone dry. The starter cranks for an extended period of time and the engine doesn't come close to firing. I have resorted to pouring a little fuel into the carb to save the starter and battery. This gets it started and it runs fine. It also starts fine after sitting a short while - a couple hours or so.

The fuel pump is new and there is always fuel in the glass bowl of the fuel filter. This, along…

Continue

interior

Posted by John Rueff on December 19, 2018 at 4:24pm 3 Comments

I would like to upholster my caddy back to original.   Does anyone know where I can look at some pictures or photos.  Also, how hard is it to remove the dash?  thanks

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service