big sigh!!!  well, i found the bleeders weren't  quite tight enough, so the last couple of runs through town i have and no brake leaks,  brakes feel ok, may have been i was so used to bad ones, didnt know what a good push was,, ANYWAY,, 

the starter....

since i replaced the starter back in november, i had the ignition switch go out,(wiring fried)  so for most of the last month, i have used the hot wire method.  seemed to do ok, just cant do it and go anywhere.  

i did notice when i used a generic 3 prong starter from parts store, i left it hooked up over night.  not on, and not in the accessory position,  the next day, the battery was dead.  charged and it started right up

So i just figured, until I get the replacement that fit with the 4 prongs, i would just hot wire, and undo the black post at night or when not in use.

so yesterday, i got all the parts in and hooked up the starter, and bammm,, fired right up,  took my rides, tested brakes,,,etc... came home parked it for an hour or two,, went back to go for another short ride, and i got that dreaded,, hard to turn over sound.  but it would turn over on about the third slow clunk and start.,, went for my ride, came back, parked and shut down for the night,, un did the black at battery.  

this morning, after checking for brake leaks, hooked it up, and it started right up like one would expect.  went for about a 20minute ride.,, came home,, went in side for about 20 minutes, came back out, and got that slow slow turn over.. it would nt start so i turned it off,, checked the battery, had appropriate cold charge volts,  waited about 45 more minutes. went out, tried it again,  tightened down the black,, got two slow turns and then it started,,took it for a ride,,, came back, test battery with engine on, and was well up in the 14's so from what i have read, it was doing what it was supposed to,

now I dont have ANY idea what to do now,  I'm fearful of turning off somewhere as it may not start.  but, i have found that after a long time, hours or so, and the battery undone, i can go out and it will do fine.  

i have been using gunk remover, and shooting water under engine cleaning the underside and engine over the last two weeks when i did nt have a working something to do on the car.  maybe some old wiring is bad? i just dont know,,could it be a fuse?  grounds are all there and tight, i mean if the starter is a non working part once the car is started, what else could cause this sort of hot start issue,, battery???  it works good cold, but not when its been on an running and then to follow up with a start.

I know yall are getting sick of my questions, but i have no were else to turn, you tube only covers so much and so much is on modern stuff...

Views: 1164

Reply to This

Replies to This Discussion

I do find it odd that the engine starts right up when warm with the timing retarded. But if all else is as it should be I would lean towards putting a known good starter back in the car with a proper set timing mark and go from there. 

Still suffering from flu!  Cant get bk out for day or two more

well, I'm back,,,sort of,, the flu really knocked me out,, at 58, it hurts and it last, still not ready to crawl under cars or smell the grease,, just doesnt sound stimulating at this point in the recovery,, anyway, second day in, knowing i was going to be out a week or more, i said crap,, just take car to shop, let them fix a trans pan leak, the oil pump gasket leak, speedometer cable leak, and then look at the starter problem.. When i told him the symptoms,, he pretty much suggested all the potential symptoms as possible, that  we have gone over and over here,, so I am hopeful, given the number of test i have told him i ran, and all the suggestions here, he should be able to quickly analyze and fix.  

i know i copped out on it at the critical moment, but i know how long the flu takes to get through and i want ed have it done by the time i got well and get those pesky little leaks fixed. so i could go for a spin,, maybe new year night take a cruise.  thanks for th al the help again,, 

I understand taking it to the shop completely! You get to the point you just want it fixed and to be able to enjoy the car!  You had a lot of patience and encourage you to continue to learn as you go along. Hopefully it will be smooth sailing when you get it out of the shop! 

Kim you didn't cop out! There is nothing wrong with having someone else look and work on the car once in awhile.  I have done it when life was too busy or too many other projects on the go. Be proud of what you've accomplished so far and I get the feeling that you will be back improving this thing more in the near future. 

Kim, be thankful that you are able to afford a mechanic. Several folks wrench on their own cars out of necessity. 

Since i pulled the car from the car shop out of frustration during my flu episode.  Starter issue is still there.  He did say there was no voltage drop from battery to starter, and he felt from limited testing,  probly starter.  Well. I got it home, and noticed the tubing that carries the yellow wire to the coil, had melted to the top of the block,  the plastic i. The wire was ok. But i was wondering if this amount of heat could reduce that wires ability to start. If indeed this wire has anything to do with my prior starter issue.  I did however, get some of thise woven cloth tubes for performance and re encased all the wires running on top of block to the coil, ,  

RSS

Photos

  • Add Photos
  • View All

Forum

Modern radio antenna …

Started by Mack in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

Just replaced radios for the modern radios with Bluetooth and all the dance things and wanted to share how I went around the antenna knob… I’ve installed a regular two way GM window switch in the…Continue

BOOT

Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Marty Smith yesterday. 1 Reply

I recently purchased a new boot for my 64 convertible and was wondering how difficult it s to install. I'm not very mechanical. It looks like the chrome piece behind and at top of seats needs to be…Continue

63 Exhaust Hanger Mystery

Started by Mike Travers in 1963/64 Cadillac Specific Discussion. Last reply by Cees de Bunje on Monday. 8 Replies

I'm in the process of installing a stainless steel single exhaust from Classic Exhaust on my '63 Coupe de Ville. I'm running into a mystery regarding my middle exhaust bracket. I have the bracket…Continue

TH400 Dipstick Tube Seal

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb on Monday. 9 Replies

In my “rebuild” of the transmission, I ordered a dipstick tube seal. However, I’m not sure if the right one came or how to best install the seal. I am wondering if anyone has replaced this seal OR…Continue

Blog Posts

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

'63 Eldorado trumpet horn + 2 standard horns restoration

Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment

My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns. 

There is a restoration service called The Horn Works who my son…

Continue

Events

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service