Hello together,

I would like to retrofit seat belts in my 1963 Fleetwood 60 Special. It has the mounting holes under the carpet.

I used the "search-box" but couldn´t find the right info.

My question is: What size does the bolts have? 7/16" ?

Due to the very few original belts available here in germany and because of their often very poor condition, I decided on this one:

CSP Seat Belts

These belts are usually used for VW Beetles, Karmann Ghia or Vans like the VW Samba Van, have the right length and are available in my interior colour.

One more thing ;-) :

I searched through the shop manual but didn´t find a help how to remove the rear seats for installing the rear seat belts (for our little daughter) 

Is it like pressing down the front egde of the seat and then pushing back to release the bracket?

Thanks in advance

Views: 33

Reply to This

Replies to This Discussion

Bolt threads in front and rear are 7/16"-20. Use Grade 8 hardened bolts.

For removing the rear seat, yes, you push down on the front of the seat and push rearward to unhook the seat frame from the hooks on the floor. This picture is in the "Help" section under "Seatbelts, Rear: Example Pictures from 1964 Sedan de Ville"

Just add top what Kurt said, when I part a car out I will often wedge my shoulders between the back of the front seat and force down and backward. Works about 90% of the time to quickly Dislodge seat from that hook.

Member Mr.Preston Bealle previously noted:

"I got this done tonight after a few weeks of fiddling around with no luck. I stuck my head on the floor with a strong flashlight, and once I saw the construction of the hooks and the location, I realized that pushing the seat down right where the hooks are is what did it quickly. I was pushing in the middle, lying on the seat, all that, with no success. Direct pressure against the area right where each hook is loosened it right away."

Also, it's great to hear that are adding the belts.  Good luck!

hth

RSS

Photos

  • Add Photos
  • View All

Forum

Start up. 1st attempt

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 5 hours ago. 21 Replies

No Description

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 9 hours ago. 234 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

64 Horns

Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Saturday. 1 Reply

I have 3 horns and the only one working is the bottom long one. The 2 round ones are not. I played around with the connections and they seem ok. I tried to check for power but not sure I was doing it…Continue

Compression test

Started by Michael Chomout in Restoration Discussion. Last reply by Karl Schwarz on Friday. 8 Replies

Dear Gents, just had time to dova compression test on the 429 engine by warming up the engine and removed all plugs and went through cranking without pouring oil into the cylinder since I want to…Continue

Blog Posts

63 Trunk detail

Posted by Bob Pontius on April 8, 2021 at 3:07pm 1 Comment

Jason, I liked the detail and information you have provided. I would like to do mine similar to yours. Can you help? Do you have trunk material? OPGI is sending the trunk product for my 63 Fleetwood. But it does cover the entire trunk as yours was done. If you do not have can you give me a reference? Thanks!! Bob

Car lift and jack stands

Posted by Les Eastling on March 23, 2021 at 10:00am 4 Comments

I mentioned during the 63/64 chapter zoom meeting on 3/21 that we had installed a car lift in our garage. Someone asked what kind and I didn't have the info at hand, so here is a link to it and also a link to some tall jack stands we use to add more stability to the car and an additional safety factor. There is something about getting underneath one of these cars that makes me a little nervous! …

Continue

Leaky Freeze Plug

Posted by Lee Martin on March 22, 2021 at 12:49pm 7 Comments

Just developed a significant leak coming from a freeze plug right over the starter.  Would this be considered a "cam plug" i.e. like Dorman 17616DS?  Our cars have multiple sizes of plugs on engine block and I want to get the right one.  Also, does anyone know how pricey this is for a shop to fix?  Thanks!

Balancer location

Posted by Kim K Kaiser on March 20, 2021 at 4:47pm 6 Comments

Readi g another thread. Does this look about right on balancer gap? Thats a 1/4 thick piece of metal.

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service