Hi guys,
Another thing that does not work well on my caddy is the rear passenger window.
Downstairs he goes quite well, but he stops at the lower limit and does not want to go on, but when he handles his hand he will go down completely.
He gets up a bit, but I have a lot to help with the rest of the way up.
What should I do with it?
Please tell the advice of the window run I was using a lithium grease.
I attach a photo and a short video.

link for short video : 

https://www.youtube.com/watch?v=VhZ-HeMBxoQ&feature=youtu.be

Views: 49

Reply to This

Replies to This Discussion

Jan
Check all electrical connections --and the GROUND -- make clean and shinny
Many things come back to life just cleaning the ground connection
You can remove the connectors to clean them and poish the metal

The window motor SB the problem as you have power going down and some up
Take it apart and see if hardened grease is the issue
Replacing the motor after the above would be the way to go

If the rear window stops work you need to check for broken wires in the driver door jam wire harness --under the rubber cover

Enjoy

Hi Tony,
thank you for the answer, the electricity should be ok, all the buttons work and it works just as if it sticks, maybe it will be the old fat, something like this I have now solved with seat transmision and there was a problem in the old lubricant.
So I want to ask what is the procedure of removing the window out of the car and the engine window?
Thank you

PS:

Tony what does it mean "motor SB" :) excuse my english isn't so good :)

I addressed the slow moving rear qtr windows in my 64 CDV about 4 1/2 years ago. I bascally had dried on grease inside the tracks, replaced motors with better motors and make sure my channels and guides were well lubricated. You can see some of my work on page 2 and 3 from my Interior Project which can be seen by Clicking Here.

SB is an abriviation for - should be

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

Upper and lower Control Arms Bushings

Started by Joe DiIaconi in General Discussion 32 minutes ago. 0 Replies

Was just thinking if You Jason and You Russ and anyone else have a surplus of Upper and lower Control Arms you might want to replace the bushings and then sell them as a whole unit. I don't know if…Continue

Fuel pump again!

Started by Chris in General Discussion 2 hours ago. 0 Replies

Hi guys, well my fuel pump decided to crap out tonight after a Sunday cruise with the family. I had to get the car towed home since it wouldn’t start.I’ve written on here before regarding issues I’ve…Continue

question on oil pump priming and pressurets

Started by Tim Bobeck in 1963/64 Cadillac Specific Discussion 6 hours ago. 0 Replies

hi everyone , I have a 63 coupe  that I have rebuilt the 390 engine. Long story short, after getting it all together and in the car, I started to prime to oil pump with a drill and socket, and I…Continue

My new project ( upper control arm bushing )

Started by Joe DiIaconi in 1963/64 Cadillac Specific Discussion. Last reply by Joe DiIaconi 7 hours ago. 3 Replies

Has anyone found a good kit to replace all of the bushings including ball joints,  tie rod inner and outer, upper and lower control arm bushings, center link. I replace mine a couple years ago, but…Continue

Blog Posts

where do I find a new and better motor?

Posted by john kilbourne on May 24, 2018 at 11:43am 11 Comments

My '64 convert is getting better, but the engine remains questionable. Starts and runs well enough, powerful, but I think I hear a main bearing banging, the balance is not great and I'd like to upgrade to fuel injection if I can.

Are there dependable remans available of good quality? Are new crate engines available? Will more advanced engines from newer years fit?

Also, please, the diff ratio is quite high, lots of RPMs compared to today's cars. Are there diffs with lower…

Continue

1963 Cadillac DeVille

Posted by Sven on May 21, 2018 at 8:00am 0 Comments

Good morning community, I have this beautiful 1963 4 door for sale, asking cad$9999, that's about us$7750. I would bring it down south over the border to North Dakota or Minnesota.

If anyone is interested, feel free to ask questions.

Otherwise what are the best websites to sell classic cars in the states?



Please view this ad:



63 cadillac deville ,…

Continue

camshaft

Posted by Dave Fundaburg on May 20, 2018 at 11:49am 1 Comment

Has anyone used the performance camshafts offered by Kanter or Isky if so how do you like the upgrade in general and how is the idle quality and vacuum for power accessories any advice would be greatly appreciated, thanks.

Door jamb switchs

Posted by Anthony Boles on May 17, 2018 at 9:50am 9 Comments

I'm having problems with the door jamb switches,the interior lights will sometimes work or the interior lights will just stay on and run the battery down ,there's three black wires spliced together and one simgle black and white wire,what could be the problem. 

Videos

  • Add Videos
  • View All

© 2018   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service