Is there a special trick to get the hood to line up properly? I can't seem to get the back of the hood to go all the way down.

Views: 156

Reply to This

Replies to This Discussion

This takes 2 people.

Person #1 holds the hood up.

person #2 loosens the bolts to the hood hinge. The bracket on the fire wall gets loosened too.

Person #1 pushed up on the hood. The intent is to lower the back of the hinge, while raising the front of the hinge up.

Loosen the brackets too, so the hinge rocks completely.

Dry hinges will hang up a hinge, so lube the hinge pivot points with a general purpose oil. WD-40 evaporates, so use something else.

If that doesn't do it, then the hinge has reached its life span.   The rivets wear, causing the hinge to flex.  Taking the spring off the hinge, you can see the movement in the hinge joints.

Yea, The first response is 100% right. I had the same issue - rebuilt the hinges (they really looked ok before rebuild) and the rebuilt hinges brought the hood right down.  

I think if you take the springs out, the hood drops into the right spot - this may be a good test for the hing wear. 

Is there kits to rebuild the hinges? How do I get them?

I have the 2 sizes of rivets needed.  They need to be machined to fit.   A complete set is 21.00

email me at 



  • Add Photos
  • View All


Trumpet Horn

Started by Ray Schick in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 4 hours ago. 1 Reply

Check out the price for the trumpet horn on eBay , that’s crazy !   Someone really wants to blow their horn at that price.Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 17 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Front Disc Conversion for ‘64 Series 62 Coupe

Started by Dan Loukota in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 18 hours ago. 6 Replies

I started a front disc brake conversion on my ‘64 Caddy. I finished the drivers side first only to find my factory rim scrapes the caliper to the point it would need spacing 1” to clear and roll…Continue

Bucket seats

Started by Gregory Lewis Freeman in 1963/64 Cadillac Specific Discussion. Last reply by Ian Osborne yesterday. 15 Replies

I'm looking fo a set of 63 64 eldo or devilleBuckets with console and door seat controllersGreg 2133059550.Continue

Blog Posts

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…


Road Trip

Posted by Ray Schick on January 21, 2020 at 9:00pm 7 Comments

Got a little cabin fever this morning,decided to take a road trip to Hickory Corners Michigan, The Gilmore Museum. It’s about 2 1/2 hours from my home . Place is awesome,I was really impressed.



1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…


Looking for the Rochester Choke Tube ...

Posted by Mack on January 10, 2020 at 1:14am 3 Comments


Looking to buy the choke tube for my Rochester... anybody have one for Sale???


  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service