per the shop couple weeks ago and a loose steering and a steering gear replacement, it was suggested the left outer tie rod be replaced,, 

I dug not the manual, and can seem to find the directions on that, but did go to you tube and saw about 4 different iterations, and while it seemed simple,, i noticed the connection point is not the same,  on the videos, they just loosen a nut, you mark the spot and then spin out the tie rod end.. on outs, it has two clamp looking items..

is the process the  same,undo those two clamps, or one of them, make the distance or count the rotations out, then spin back in the new one at the same rotations..?

I'm aware it will have to be re aligned, but want to make sure the process is same,, just a different measuring and connection mechanism.??

sincerely

Views: 126

Reply to This

Replies to This Discussion

Kim, you'll only loosen  the outer clamp next to the outer tie rod joint. Leave the inner clamp tight on the inner tie rod. Remove the outer tie rod pivot from the knuckle. Measure the outer tie rod from the edge of the adjuster sleeve to the center of the pivot stud big end. Remove the old tie rod end from the adjuster sleeve. Install the new tie rod end  to the same measurement as the old one was. Put the pivot stud in the steering knuckle torqued to spec. Then tighten the adjuster sleeve clamp. You'll need to get an alignment after you finish your install.  HTH

I got that thing off,  had to get that tuning fork piece to separaye it.  

Getting back on was no prob.  I deceded to order the other side as well as i am in get stuff done mode and will take in for realignment so both sides will hv new parts.  Made sense to me.

I am really surprised at how just changing the one side improved my steering,   i had about a 3 to 4 inch looseness on each side of the steering wheel.  It was enoigh for me to not like driving at night because the over steer and compensation to get back made me look like inwas drinking.  

Anyway, seems to have worked, otherside replacement may get it completely tuned in with alignment.

Thanks again

Thanks, that gave me the clarificaion i needed on the connections

RSS

Photos

  • Add Photos
  • View All

Forum

Modern radio antenna …

Started by Mack in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

Just replaced radios for the modern radios with Bluetooth and all the dance things and wanted to share how I went around the antenna knob… I’ve installed a regular two way GM window switch in the…Continue

BOOT

Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Marty Smith yesterday. 1 Reply

I recently purchased a new boot for my 64 convertible and was wondering how difficult it s to install. I'm not very mechanical. It looks like the chrome piece behind and at top of seats needs to be…Continue

63 Exhaust Hanger Mystery

Started by Mike Travers in 1963/64 Cadillac Specific Discussion. Last reply by Cees de Bunje on Monday. 8 Replies

I'm in the process of installing a stainless steel single exhaust from Classic Exhaust on my '63 Coupe de Ville. I'm running into a mystery regarding my middle exhaust bracket. I have the bracket…Continue

TH400 Dipstick Tube Seal

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb on Monday. 9 Replies

In my “rebuild” of the transmission, I ordered a dipstick tube seal. However, I’m not sure if the right one came or how to best install the seal. I am wondering if anyone has replaced this seal OR…Continue

Blog Posts

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

'63 Eldorado trumpet horn + 2 standard horns restoration

Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment

My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns. 

There is a restoration service called The Horn Works who my son…

Continue

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service