per the shop couple weeks ago and a loose steering and a steering gear replacement, it was suggested the left outer tie rod be replaced,, 

I dug not the manual, and can seem to find the directions on that, but did go to you tube and saw about 4 different iterations, and while it seemed simple,, i noticed the connection point is not the same,  on the videos, they just loosen a nut, you mark the spot and then spin out the tie rod end.. on outs, it has two clamp looking items..

is the process the  same,undo those two clamps, or one of them, make the distance or count the rotations out, then spin back in the new one at the same rotations..?

I'm aware it will have to be re aligned, but want to make sure the process is same,, just a different measuring and connection mechanism.??

sincerely

Views: 36

Reply to This

Replies to This Discussion

Kim, you'll only loosen  the outer clamp next to the outer tie rod joint. Leave the inner clamp tight on the inner tie rod. Remove the outer tie rod pivot from the knuckle. Measure the outer tie rod from the edge of the adjuster sleeve to the center of the pivot stud big end. Remove the old tie rod end from the adjuster sleeve. Install the new tie rod end  to the same measurement as the old one was. Put the pivot stud in the steering knuckle torqued to spec. Then tighten the adjuster sleeve clamp. You'll need to get an alignment after you finish your install.  HTH

I got that thing off,  had to get that tuning fork piece to separaye it.  

Getting back on was no prob.  I deceded to order the other side as well as i am in get stuff done mode and will take in for realignment so both sides will hv new parts.  Made sense to me.

I am really surprised at how just changing the one side improved my steering,   i had about a 3 to 4 inch looseness on each side of the steering wheel.  It was enoigh for me to not like driving at night because the over steer and compensation to get back made me look like inwas drinking.  

Anyway, seems to have worked, otherside replacement may get it completely tuned in with alignment.

Thanks again

Thanks, that gave me the clarificaion i needed on the connections

RSS

Photos

  • Add Photos
  • View All

Forum

Convertible Top Cylinder Removal

Started by Brian Wiseman in 1963/64 Cadillac Specific Discussion. Last reply by Chris Codd 16 hours ago. 7 Replies

Just wanted to check before removing my 1964 convertible top cylinders.  I have the instructions from the 1964 shop manual.  I have identified, in Red #s, the bolts in the procedure with the images. …Continue

Input appreciated on a transmission issue

Started by Tosh Dickenson in General Discussion. Last reply by Tony and Ginny 429 17 hours ago. 11 Replies

Finally a sunny day to drive the Caddy into work!Alas when I set off down the road, I realized she wasn't shifting from first to any higher range.  I just drove it on Saturday and it was shifting…Continue

Mirror Passenger Side

Started by Bob Ricks in Wanted to Buy. Last reply by Bob Ricks 18 hours ago. 2 Replies

Seeking a Passenger Side Exterior Door Mirror.   Doesn't need to be perfect.1963 Caddy Coupe DevilleContinue

Headliner insulation

Started by Robert Alan Shannon in 1963/64 Cadillac Specific Discussion. Last reply by Robert Alan Shannon 19 hours ago. 4 Replies

 I have a question about the padding  used between the  headliner and  interior roof of hardtops . It's abt 1/8" thick and  I  want to remove this from my parts car because I use it for storage ;…Continue

Tags: padding, Headliner

Blog Posts

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…

Continue

Road Trip

Posted by Ray Schick on January 21, 2020 at 9:00pm 7 Comments

Got a little cabin fever this morning,decided to take a road trip to Hickory Corners Michigan, The Gilmore Museum. It’s about 2 1/2 hours from my home . Place is awesome,I was really impressed.

9A648CFF-E965-4CE0-8E91-8E194AC70DED.jpeg…



Continue

1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…

Continue

Looking for the Rochester Choke Tube ...

Posted by Mack on January 10, 2020 at 1:14am 3 Comments

37E244B6-71C7-4857-8D50-1BD8C48077A4.jpeg

Looking to buy the choke tube for my Rochester... anybody have one for Sale???

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service