Good morning to all my fellow 63/64 Caddy friends,

I have a problem with my convertible top operation that has left me puzzled.

When opening and closing it, the process has become painfully slow. When raising (closing) the roof, it actually stops in the middle of the process and only works after I leave the switch alone for a minutes or two.

I thought it might the oil in the pump and followed the Manual to purge and fill it with transmission oil. There was none missing, but followed the steps in the Shop Manual anyway.  But this did not solve the issue.

What can be the cause of this slowness and actually stopping?

Thank you to all who might have any idea what can be the cause.

Views: 50

Reply to This

Replies to This Discussion

The motor is overheating and the internal circuit breaker is activating.  Try a little lube at the hinge points. A silicone spray might work.

I haven't worked with a convertible so I don't know. But does it have grease that could be dried and seize the operations in the same way as the transmission for the power seat?

Sounds like the electrical motor part of the hydraulic pump is the problem overheating

You can lube the hydraulic cylinders Arms ---on both sides of the back seat with brake fluid per the manual to see if that allows them to move more freely ( less resistance on the motor )

If you can get to the motor brushes on the armature check them for wear
Not sure if replacement brushes are available but others should chime in on that

Replace the motor if all else fails
Good chance you can find a replacement motor on this site

Enjoy

Groundhog day Tony, I posted that stuff earlier.

Looks like Tony went into considerably more detail.  Again, we have no rule where only one reply per question. In fact, it is better to get feedback from everyone than stay quiet if someone answers something.  We all have different experiences and knowledge and the more feedback the better. There have been lots of examples of topic discussions here on the forums where I think I have the complete picture and someone adds a bit more detail that I had not considered or did not know. 

Russ

Just seconding your thoughts is all

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

off the wall question

Started by James Fejerang in 1963/64 Cadillac Specific Discussion. Last reply by Ray Schick 23 minutes ago. 1 Reply

 Could anyone please tell me why on some models of the 64 devilles, the Bezel, Turn signal (LH upper) is clear and the other one RH Bezel is chrome.  Sorry if this is a stupid question, but i have…Continue

fuel pump

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Anders 2 hours ago. 4 Replies

I am gathering up some stuff to put away for the potential trip home in oct/nov from MT to MS in the 63 cdv.i thought a fuel pump may be a good piece to have nearby,  Are the newer ones like you can…Continue

rear seat speaker grill

Started by Kenneth R Hudgins in 1963/64 Cadillac Specific Discussion 11 hours ago. 0 Replies

Looking for a rear seat speaker grill for my 63 EldoradoContinue

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 159 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

Starter Solenoid replacement-how difficult? Where to buy?

Posted by Norman Silverman on August 20, 2019 at 8:24pm 8 Comments

Hello All.

I believe the starter solenoid has gone bad in my 64 DeVille. When I turn the key, often all I get is a click, then if I try a few times again the starter turns perfectly. All battery cables are on tight and the battery is good. So, I believe this problem is the solenoid. Where do I buy the right solenoid and is it necessary to remove the starter in order to swap it out? …

Continue

Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…

Continue

Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.

Thanks

Dominic

Upper A Arm Rubber Bumpers

Posted by Gene McIlroy on August 12, 2019 at 1:30pm 3 Comments

I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service