Hi All

am putting the 63 Convertible back together

am currently putting the front goodies on

i have operating turn signals but no cornering lights

i jumped power directly from the battery....they both work

i checked the orange wire on each side.....no power

all connections under the dash are tight

my turn signal lever was bent upwards 90 degrees by some dipshit at the bead blaster location

i am wondering if there is an issue there or if I should look elsewhere 

i have an extra turn signal switch....and am going to hook it op and see what happens

any other ideas?

thx

mark

Views: 141

Reply to This

Replies to This Discussion

Test light time..... :-)

About all you can do is find where you do have power and work your way towards the lamps themselves.

Update

tried the extra turn signal switch.....no change

not sure where to go

i checked orange wire on firewall side of wiring block.....no power there 

checked turn signal as follows

R On

LT BLUE and PURPLE have volts

YELLOW/BL and WHITE no volts

L On

PINK and DK BLUE have voltage

ORANGE and WHITE no volts

Mark, i hate auto electrics with a passion and would rather give myself a frontal lobotomy than be dicking around with wires.

A test light search is about as far as I go before calling a sparkie. Someone with more smarts than me (Not too hard) will be along shortly to help you out.  

Frontal lobotomy or bottle infrontofme?

Mark

I wrote up a thead in the --search engine--( top right of the home page ) here when trouble shooting my same cornering light problems that i repaired
Sure some of the info will be very helpful
Under -- steering wheel removal --there

Enjoy

Kevin

Good timing as i see it !!!!!!!!!

Hey, good to see you came back again..... :-)

Another update

no power to the DARK GREEN  wire either

Mark, Are you checking them with the parking lights or headlights on? That's the only time they are supposed to work.

Ha ha, who hasn't done that at some time.... LOL.

Years ago, I was chuckin a sad, Jesus H Christ, I had a power a minute ago....  rant.... rave... carry on like an idiot, to then realize, i'd turned the ignition back off. :-)

Mark
When you go to the steering wheel removal thread ( in the search engine ) -i suggested you will have to go to the very last page of all those threads - PAGE NUMBER 8
There you will find my write up on getting the cornering lightts tested and repaired
All the threads of mine before that are not as complete as that very last one
Open the thread and my detail instructions (posted by Tony and ginny 429 )
Will begin with --status --and start by explaining --to be removing the plate under the steering column and continue foward from there

Searching for my final thoughts on that thread can seem confusing ( as i scanned thru it myself ) as the thread was unfolding and developing into the final thread by me --on page 8 --of those threads
The info there should direct you on how to --get to the turn signal switch inside the steering column by removing the steering wheel
A lot of details that should be very helpful in getting that task done as they are not as complete as the last one where i did my final write up on the repair

Enjoy ( or your doing something wrong ! )

Sorry for any confussion all the prior posts there may have been causing

Thank u all for the help

i really had no issue other than realizing the damn corner lights don’t work unless you have the headlights on

i feel like such a dipshit

the bright side is I learned some new skills with the multimeter

on a different note, finished the front bumper/grille today

something to note....

when assembling this he grille, the top crossmember must come off

this gives you room to get the top half of the grille with the chrome piece still attached

Attachments:

RSS

Photos

  • Add Photos
  • View All

Forum

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 2 hours ago. 165 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Looking for 64 to 66 seat belt buckles, male and female together.

Started by Ryan Frawley in Wanted to Buy. Last reply by Tony and Ginny 429 yesterday. 5 Replies

Hey all, I am in the process of finishing up my 64 coupe deville and noticed that the front seat belts only have the retractor side in the bag I put all the belts in when I got it. I have found it…Continue

Tags: buckle, safety belt, seatbelt, seatbelts

Movie Star Cars.

Started by Kevin Campbell in General Discussion. Last reply by Kurt yesterday. 17 Replies

We have the Village Roadshow film studios about an 1.5 hour drive away.They've put out a call for cars to appear in a movie about Elvis. :-)So, I nominated our 64 Fleetwood as a potential "Movie Star…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

Stuck at two red (dash) lights!

Posted by Jeff Kinzler on November 3, 2019 at 10:00pm 9 Comments

I hope someone can help solve these two electrical problems that appeared one after the other.

By way of background: The car, a '64 Eldorado has very limited use. It was at a restoration shop for 15 months until last January-  that supposedly did a bunch of wiring repairs including rebuilding the gas gauge that still hasn't worked properly, and the clock that hasn't worked, and re-soldering the broken wires in the drive door. All window and seat controls appear to be…

Continue

driveshaft help

Posted by wayne weaver on October 9, 2019 at 4:41pm 1 Comment

can anyone help me with a driveshaft ? I have a 1963 Cadillac 62 series 4dr with the hydro-matic trans. I need the male splined shaft on the front of the rear driveshaft section. the piece with the nut attached by clip.id be willing to buy a shaft if its not horribly priced.

Dash removal

Posted by Jake Mickley on October 9, 2019 at 12:06am 9 Comments

Hello everyone,

On a 63 CDV, if a guy wanted to remove the entire dash to get all the metal painted, and do some other things behind there, how would he go about doing that?  I checked here and the shop manual, but can't find a complete guide.

As always, and help or direction is appreciated.  Thanks!

--Jake

Introducing myself

Posted by Gary Marchand on October 7, 2019 at 9:32pm 8 Comments

Thanks for letting me join the club.  Picked up this ‘64 Coupe Deville a few months ago out of Beverly MA, the car has few stickers on it from various Cadillac clubs, didn’t know if anyone might recognize it from it’s “Glory days.” Everything seems pretty healthy except for the body and some very Mickey Mouse repairs, was wondering if anyone had any leads on…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service