i pulled out the master cylinder after it developed another leaking issue, similar to the one I had five years ago.  I replaced the seals then, but decided to replace the master cylinder this time.  The part I have came without the seal that looks like a piece of sponge, fitted around the end that is bolted to the brake booster.  My old part is completely disintegrated and not transferable.  

What is the purpose of this ‘seal’ and does anyone have experience of not fitting one, or fitting an alternative?

Views: 123

Reply to This

Replies to This Discussion

This is not a seal, it's an air filter.  The master cylinder mating bore is the exhaust for the vacuum when you release the brake, to refill the diaphragm.    There is another one inside the cabin on the pedal side.    
 Be wary that if air can't enter there, the brakes will lock up after you use the brakes a certain number of times.  I had that problem with a caddy once, where there was a moraine booster used to replace a bendix, and the wrong breather (or both, i don't remember) was installed.    The vacuum had no way to release, and the brakes would start smelling after about 20 min of driving.

Thanks for the info Mark.  I have not been able to find one of these on the usual sites, do you know if this needs to be something specific, or would an open pore foam (fashioned into the correct form/size) suffice?

Hi Mark,

i endedup making a filter out of foam (I hope it works). But, when I was comparing the two parts (old and new) although I can see the air hole, it seemed to be covered over with a dust seal or boot.  I can’t see this part in the shop manual.  Fitting this boot will stop any air exhausting, as it’s a tight Durand in my case, it seems to have been siliconed in, to ensure a tight fit.  Any info on this part?

ive uploaded photos

thanks,

David

Attachments:

the silicone is unnecessary, maybe even would cause problems.   

your setup looks to be as it was, with the difference that the seal installed at the factory was felt and not sponge.   It should work.   If you smell brake shoes burning after a medium length drive, you will need to change it.    The filter is only there to keep dirt from being sucked into the power valve when the pedal is released.  the brakes can work without.
 

That said, it looks like you've done great to even look into it, most people toss them, so they are rare these days.  

Thanks Mark.

greatly appreciate your feedback.  

David

Any chance we can get a visual ( photo ) of this air filter for the MC as this is the very first I have heard of this air filter 

As always — Thanks Mark 

Enjoy 

Tony, There is an illustration in your shop manual of both filters. The Bendix had a different setup. They vented from the cap as I recall, but had the incab filter like the DM.

Thank you Jason 

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

Start up. 1st attempt

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kim K Kaiser 1 hour ago. 16 Replies

No Description

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 4 hours ago. 233 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

64 Horns

Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 1 Reply

I have 3 horns and the only one working is the bottom long one. The 2 round ones are not. I played around with the connections and they seem ok. I tried to check for power but not sure I was doing it…Continue

Compression test

Started by Michael Chomout in Restoration Discussion. Last reply by Karl Schwarz on Friday. 8 Replies

Dear Gents, just had time to dova compression test on the 429 engine by warming up the engine and removed all plugs and went through cranking without pouring oil into the cylinder since I want to…Continue

Blog Posts

63 Trunk detail

Posted by Bob Pontius on April 8, 2021 at 3:07pm 1 Comment

Jason, I liked the detail and information you have provided. I would like to do mine similar to yours. Can you help? Do you have trunk material? OPGI is sending the trunk product for my 63 Fleetwood. But it does cover the entire trunk as yours was done. If you do not have can you give me a reference? Thanks!! Bob

Car lift and jack stands

Posted by Les Eastling on March 23, 2021 at 10:00am 4 Comments

I mentioned during the 63/64 chapter zoom meeting on 3/21 that we had installed a car lift in our garage. Someone asked what kind and I didn't have the info at hand, so here is a link to it and also a link to some tall jack stands we use to add more stability to the car and an additional safety factor. There is something about getting underneath one of these cars that makes me a little nervous! …

Continue

Leaky Freeze Plug

Posted by Lee Martin on March 22, 2021 at 12:49pm 7 Comments

Just developed a significant leak coming from a freeze plug right over the starter.  Would this be considered a "cam plug" i.e. like Dorman 17616DS?  Our cars have multiple sizes of plugs on engine block and I want to get the right one.  Also, does anyone know how pricey this is for a shop to fix?  Thanks!

Balancer location

Posted by Kim K Kaiser on March 20, 2021 at 4:47pm 6 Comments

Readi g another thread. Does this look about right on balancer gap? Thats a 1/4 thick piece of metal.

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service