I have been looking for one of these for a couple of years. If anyone knows where I can buy one, or if you have one for sale please let me know belt Tension Adjusting wrench J-9646

Views: 77

Reply to This

Replies to This Discussion

Should be easy enough to make for a machine shop.

Joe D

You can use any kind of crow bar you can fit between the compressor and the compressor mount To give you --the leverage you will need there
After loosening the compressor mounting bolts ( do keep them snug but not tight so the compressor can move when pressure is applied )
Pull on the crow bar to move the compressor to tighten the fan belt
When you have a 1/2 inch play in the fan belt at its longest span the belt is adjusted correctly
Tighten all down
Task done correctly --without needing the special tool
Just the crow bar in the corner of the tool box -LOL

Enjoy

Joe D

Disregard the breaker bar post
I deleted that post after looking at the tool again but it still is showing on the dashboard home page anyway
There is an additional flat metal part to the tool that i did not see at first
My earlier suggestion should get the belt adjusted correctly and that looks like the goal here

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

Turn signal

Started by Jeroen Welgemoed in 1963/64 Cadillac Specific Discussion. Last reply by Jeroen Welgemoed 2 hours ago. 4 Replies

Hi all. It has been a while since i last asked or posted something. My car has his engine put back in and i am now just working om some loose ends.The last thing i have to do before i can get on the…Continue

New transmission mounts for sale.

Started by Russ Austin in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 12 hours ago. 1 Reply

I have 3 new transmission mounts for the 64 Turbo Hydromatic.  New from Steelerubber, still in the bag. I took one out to take a picture.These retail for 127.40  but you can get them from me for…Continue

63 jetaway transmission

Started by Scott L Foltz in Restoration Discussion. Last reply by Russ Austin 16 hours ago. 4 Replies

Hello and thank you for letting me join this group. While I was driving my 63 model 62 my trans cooler line blew off and needless to say I ran out of fluid. The next day I replaced the rubber hose…Continue

Tags: Transmission

CLC 2019 Grand National - Louisville, Kentucky, June 11-15, 2019

Started by Jason Edge in General Discussion. Last reply by Marty Smith 22 hours ago. 35 Replies

1963/64 Cadillac Chapter 2019 Grand National Page www.2019GN.6364Cadillac.com…Continue

Tags: National, Grand, CLC, 2019

Blog Posts

Cadillac Returns to its Roots Under New Leadership

Posted by Jeff Kinzler on May 1, 2019 at 12:30am 3 Comments

Cadillac’s new boss says they should stop trying to build BMWs and go back to building Cadillacs again.

What do you think? 

https://carbuzz.com/news/cadillac-finally-admits-what-everyone-knew-for-years

Radiator And Shrouds

Posted by Dominic Salemi on April 24, 2019 at 3:36pm 1 Comment

Hello

Anyone have a decent radiator and shrouds and hardware for a 1964 Cadillac deville. I have an alum. radiator and I'm deciding on to fix it or back to the original one. If I fix it I won't need parts.

Thanks

64 Recirc/Fresh Air Door Actuator replaced; FROM THE INSIDE.

Posted by Norman Silverman on February 4, 2019 at 11:21pm 8 Comments

I am happy to report that I have successfully replaced the Fresh Air/Recirc door actuator that is located on the blower box-and have done so without having to remove the blower box. I did it by taking out the glove box and attacking it from the back.  It took several days, LOTS of patience and some band-aids, but it is done. THE most difficult part -BY FAR- is to remove and then replace the screw that sits on the actuator arm, connecting it to the fresh…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service