We often have discussions regarding the location of ground straps and the fact they can often cause electrical failure when not attached or not securely attached. Below is a run-down of the ground straps used. This post will be updated with additional pictures and info in the future and will be added to the Help Topics page.

Negative Battery Cable
These originally came with spring ring terminal type cables, but have often been replaced with bolt terminal cables over the years. Either type is fine, however, you need a clean tight metal to metal connection as with all ground connections!
Below is a picture of a original type spring ring terminal negative battery cable.

Below is a picture showing an original type spring ring negative cable with the short braided harness that attaches to radiator support:

Negative Battery Cable to Frame and Radiator Support
Battery cable negative to frame and short braided harness from bottom of battery cable to radiator support..where you have lots of electronics attached to or feeding through.  I often see newer bolt terminal cables installed on these cars with no ground back to the radiator support and wonder if that degrades the current flow.

Picture below shows the bottom of the negative cable connected to the frame; the short braided ground strap attached to radiator support. You can also see in this picture the right/passenger side forward lamp harness small ground wire attached to the frame all in that same picture.  That's 3 grounds in one area.



Right Frame Rail to Engine:

Very large heavy gauge ground strap from right frame rail just underneath the firewall cowl area, over to engine block at transmission. This is the main culprit for ground related starting problems. Here is a picture mounted on the frame which is just above the front transmission cross-member location:

Forward Lamp Harness to Frame
just in front of the radiator support on both left and right side (will cause headlights to not work. See picture above for example of Right side and the picture below of Left Side which is just beside the VIN # stamped on front frame rail:

 

Left and Right Cylinder Head to Firewall/Cowl Ground Straps
One ground strap from back of each cylinder head to firewall/cowl. 
See pictures below:

RIGHT SIDE CYLINDER HEAD TO FIREWALL:
LEFT SIDE CYLINDER HEAD TO FIREWALL:


Voltage Regulator Harness to Radiator Support
Small black ground wire mounts thru lower left base of voltage regulator bracket to radiator support.

Antenna Cable Ground

Attaches to firewall on lower right side near where cable comes through firewall. 


Dash Harness Ground
The dash harness ground wire attaches to the metal dash framing at the section of the dash near the center that attaches to the firewall.

Several Other Smaller Ground Straps
 There are many other grounds throughout the car such as the  AC compressor to water outlet pipe cover bolt, wiper motor to attaching bolt, power seat motor to seat rail, fuel sending unit to frame, front upper control arm to frame, etc. Also the relays such as horn, seat/window (on 64), etc generally complete the "control/feed" circuit by way of ground to the body somewhere.

Views: 3611

Reply to This

Replies to This Discussion

Awesome Jason!  Thanks for the info...

Thanks, Todd. I just added 5 new pictures, 4 from the current parts car, showing additional ground strap locations.  The forward lamp harness and cylinder head to firewall show a lot of corrosion built up over 50+ years and one reason why these need to be inspected, cleaned, and reinstalled to make sure you have solid metal to metal contact. 

Can someone post the location on the engine where the right frame rail to engine attaches on the engine? I seem to not have that ground. Could be one of the issues with my starter

The ground strap is attached to the flywheel housing --just in front of the starter --where the starter bolts into it --on one side of the ground strap
The other side of the strap --is bolted to the the right side of the frame rail

It is a bit of a difficult picture to take when you get one side of the strap you cannot see the other side of it from the photos of that strap i have viewed

Enjoy

Another ground you would want to be very clean --is the ground on the regulator to help keep the charging system working reliably

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

The Central Florida weather could just not get any better !!

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 1 minute ago. 1 Reply

No Description

Wanted: retaining clips for dash pad legs

Started by Mark Geertsma in Wanted to Buy. Last reply by Russ Austin 6 hours ago. 1 Reply

Looking for the retaining clips (L+R) that the "legs" of the dashpad snap into. Mine are missing. Continue

1964 429 & Trans For Sale

Started by Russ in For Sale 15 hours ago. 0 Replies

Anyone in need of a 429 & trans? Was running when pulled from car but had low compression on a few cylinders if memory serves me right. Engine/trans are in Phoenix. Russ, 562.858.6926Continue

Center bearing - replacement.

Started by Anders in Restoration Discussion. Last reply by Norman Silverman 18 hours ago. 22 Replies

Had some sound from the propeller shaft and as the rear wheel bearings just been replaced I thought it would be the center bearing. Removed the propeller shaft and checked the center bearing (as per…Continue

Blog Posts

64 Recirc/Fresh Air Door Actuator replaced; FROM THE INSIDE.

Posted by Norman Silverman on February 4, 2019 at 11:21pm 8 Comments

I am happy to report that I have successfully replaced the Fresh Air/Recirc door actuator that is located on the blower box-and have done so without having to remove the blower box. I did it by taking out the glove box and attacking it from the back.  It took several days, LOTS of patience and some band-aids, but it is done. THE most difficult part -BY FAR- is to remove and then replace the screw that sits on the actuator arm, connecting it to the fresh…

Continue

Flashers

Posted by Mike Petrey on January 13, 2019 at 12:25pm 7 Comments

Where do the flashers go in my 64 Deville Convert.  I'm thinking that's why both turn signals stopped working.

Source for Motor mounts and Trans mounts 1964 SDV

Posted by Norman Silverman on January 9, 2019 at 4:23pm 4 Comments

Hi.

Where is the best place to purchase good quality motor mounts/trans mounts for my 1964 SDV? I see that Rock Auto has them for $8 and change, and others for $24 and change. Big difference. Is there a better place to buy them from?

Thanks

Norm

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service