18 years back and many miles since, I replaced the Factory original Mode Actuator and heater core. Well, a couple of weeks back the replacement Mode Actuator failed. I ordered a new Actuator from Old Air Products. I figured even though the Heater core was still good, not leaking, I might as well replace it while I had everything apart. I ordered the new heater core from Rock Auto. I have the Heater Box assembled but I haven't installed it under the dash, yet. For anyone interested, I uploaded to my page, some pictures of the Heater Box, etc. I was able to remove the Heater Box from under the dash without removing the blower housing from the engine bay firewall or removing the hood hinge, as the shop manual lists to do.

Views: 121

Reply to This

Replies to This Discussion

David 

Nice work on the 63 Ac heat box and  the fuel pump 

You got me thinking ( reminding me ) about jumping into  doing my 64 comfort control which I have purchased all the parts for a short while ago 

Been to hot in Florida but the weather will be getting real sweet very soon 

I  realize I am hung up on what to do about removing  the passenger hood hinge to get the project started as I do need to get into the blower box myself 

That engine hood is a serious heavy weight item to be dealing with 

Most of all I miss  not having my heater working for those —brisk very cool  nights  coming home from a day out with the top down

The 429 buts out enough heat when called on  to heat a small apartment building —LOL !

Always enough heat to keep the front seat extremely comfortable with the top down 

I seldom use the AC because the top is always down but I still need to have it working correctly in my pride and joy 

Enjoy 

Hi Tony, thanks for the kind words. As Russ and I stated, no need to remove the hood or hinge to get the under dash ductwork out. There are 6 speed nuts securing the duct to the firewall. All can be removed with a deep well  1/4 inch drive socket and long extensions and a universal joint. The nut under the hinge area will require a little fanagling, but it is doable.

The Airtex fuel pump failed at 15k miles. It spit the intake valve out. As you can see in the picture,  it was not staked in at the factory. 

Understood about getting the under dash air box out with the  passenger hinge  in place 

Can the blower motor box and the evaporator with the suction valve ( on the inner fender ) be remove as well with the hinge in place even if it takes a bit more effort doing it that way ? 

I do have a 64 with comfort control so the 63 SB a bit different design than mine 

Enjoy 

On the 63, I think the blower housing could be removed after removing the heater box without having to remove the hinge. I've never removed the evaporator,  but would think it would then be removed following the shop manual steps.

David 

Removing the under dash air box and then the blower box sounds like a good plan 

With the blower box out should be easier to get to the evaporator out  to check it’s condition 

Working around the hinge looks like a good plan  from the posts here 

Enjoy 

David 

It is possible to epoxy glue the valve in the fuel pump to hold it in place permanently 

Epoxy is gasoline proof and I have repaired fuel pumps in the past with it that held up for the very long haul 

i clean the surface with 91 % alcohol first 

Just another way to get that repaired done to last 

Hard to believe the valve was never installed correctly by the manufacture so most should pass on the Airtech  brand unless they choose to do this repair before installing the fuel pump into the car now being aware of the problem with the brand 

 The  Airtech fuel pumps are short lived as a rule due to  the manufacturers oversight if the problem is not addressed 

Russ was the first one I remember  to bring this to the attention of the community 

Enjoy 

I'm still chasing vacuum leaks on the 63 A/C system.  Trying to remove the A/C control switch panel so I can check the vacuum switch. The shop manual says after unbolting and disconnecting the switch assembly, to remove it from the dash.  I haven't been able to thread it out of the dash going up or down. Has anyone had success, what am I  missing? Thanks.

I remove them with the entire dash out so that will not help you but looking at the 63 & 64 shop manuals, the 63 say to disconnect the left AC outlet hose (note 15.a pg 15-9), and of course on note 14a. you have a series of disconnects such as Bowden cables, etcs. and assume hall have been disconnected, lower instrument (dash) panel removed etc. The other thing I noticed is the 64 shop manual did say to bring it out from the top ... but the 64's other than the series 75, have a different shaped, upper steering column hanger bracket, so that might be why the difference. Regardless, it will probably just take a good light and some patience and be ready to temporarily disconnect or move things. It is busy back behind there. 

Thanks Jason.  The path looked better going out the top but I couldn't get it past the speedometer and upper cowl. I became frustrated after about an hour of twisting and turning it all around and decided to call it a day. I'll go back at it in a day or so to see if I can get it to cooperate. Maybe someone else has been there and can give us some pointers on getting it removed.

Move the fuse box out of the way. 

Thanks Russ. I suspected that you or Jason had been there before. I'll try that when I get back to it.

 I was able to get the A/C control panel out this morning. As Jason suggest from the 64 shop manual it came out the top. I did have to remove the headlight switch to get clearance and even then it was tight. I tried moving the fuse panel as Russ suggested but that didn't work out.

Is there a way to restore the A/C 6 port vacuum switch? Are there sources for new replacements? The one in my 63 seems to have a good amount of seepage to it. The 3 port heat control switch seeps a little, but not as much as the 6 port.

After removing the headlight switch I noticed the Ceramic around the dash light resistor was broken. Can that be repaired with JB weld or something similar? It is in two pieces held together by the resistor wire.

RSS

Photos

  • Add Photos
  • View All

Forum

Rear main Follow up replacement and repair,,

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 49 minutes ago. 40 Replies

Well, got it all together,, Jason, i was looking in the wrong chapter in the manual on the starter,, got that figured out.  everything hooked back upGot it put back together, started up, and oil…Continue

need parts to rebuilt hydramatic transmission gearbox.

Started by Tanguy J. ROSEZ in 1963/64 Cadillac Specific Discussion. Last reply by Robert Alan Shannon 3 hours ago. 1 Reply

Hello everybody, I am from France, and I need to rebuilt the HydraMatic transmission on my 1963 PND2D1LR. Could you give me some good Professional adresses in US to buy the parts ?Continue

Henry Leland- founder of Cadillac and Lincoln

Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 21 hours ago. 1 Reply

Here's a good article about Henry Leland. I had heard bits & pieces of his story over the years but didn't know all these details.…Continue

1963 Cadillac Convertible Door Jamb Switch

Started by Lee Martin in 1963/64 Cadillac Specific Discussion. Last reply by Lee Martin on Friday. 3 Replies

Okay, it's "dumb question time!"  Here's mine:  Does anyone know the part number for the 63 convertible door jamb switch (3 prong)?  I cannot find this in the manual...thanks!Continue

Blog Posts

driveshaft help

Posted by wayne weaver on October 9, 2019 at 4:41pm 1 Comment

can anyone help me with a driveshaft ? I have a 1963 Cadillac 62 series 4dr with the hydro-matic trans. I need the male splined shaft on the front of the rear driveshaft section. the piece with the nut attached by clip.id be willing to buy a shaft if its not horribly priced.

Dash removal

Posted by Jake Mickley on October 9, 2019 at 12:06am 9 Comments

Hello everyone,

On a 63 CDV, if a guy wanted to remove the entire dash to get all the metal painted, and do some other things behind there, how would he go about doing that?  I checked here and the shop manual, but can't find a complete guide.

As always, and help or direction is appreciated.  Thanks!

--Jake

Introducing myself

Posted by Gary Marchand on October 7, 2019 at 9:32pm 8 Comments

Thanks for letting me join the club.  Picked up this ‘64 Coupe Deville a few months ago out of Beverly MA, the car has few stickers on it from various Cadillac clubs, didn’t know if anyone might recognize it from it’s “Glory days.” Everything seems pretty healthy except for the body and some very Mickey Mouse repairs, was wondering if anyone had any leads on…

Continue

Carter AFB carburetor question

Posted by Ray Schick on October 7, 2019 at 8:29pm 8 Comments

3655S carb, and a 3656S carb .I know the difference is one is for A/C and the other in for a non A/C car . Now the question is : can I use the carb bowl from the A/C car on the non A/C car ? They look the same set up next to each other

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service