Now, I know most of you guys are still in yesterday, but because Australia is such a hip, swinging sort of place down under, we get your tomorrow today, so if I waited until tomorrow, it would bugger up today.

So, I say to Dino Edge, Mr and Mrs Edge's little boy, hmmm, maybe not so little.

HAPPY BIRTHDAY Dino. I hope you get a nice cake, some presents, a party and maybe, (here's a good idea), maybe Mum and Dad will take you out to dinner on your birthday.

Views: 26

Reply to This

Replies to This Discussion

Thanks, Kevin. I'll have to remind Dino he's an old dude of 55 tomorrow...ah, I meant today for down under time! LOL I think he will be impressed that you remembered his birthday!!  ….hmm. And I had almost let it slip by! Bad on me!

From Uncle Kev and Aunty Astrid....

https://www.youtube.com/watch?v=pjfst1CgFcE

Hi Jason, hey mate, i had no idea you had a newsletter due out on ol Dino's birthday with a feature on him.=. (good read too)

Because we are a day ahead of you hillbillies, I hope I didn't steal your thunder by posting this thread.

Might you, if you talk to the wife, apparently, i'm very good at "jumping the gun" sometimes. :-) 

No Problem, Technically it was Dino's B'day down under... although Ye Olde 3rd Rock would have to rotate a bit before Dino rolled off the Clark St assembly line in Detroit.  The new pictures next to the Garner coffee house was taken this past week but felt compelled to pull he olde dude out today as seen below. Plan to run in, grab a bit to eat and gas'em up and do a bit of cruising to celebrate the birthday boy!

RSS

Photos

  • Add Photos
  • View All

Forum

Wanted: retaining clips for dash pad legs

Started by Mark Geertsma in Wanted to Buy. Last reply by Russ Austin 6 hours ago. 1 Reply

Looking for the retaining clips (L+R) that the "legs" of the dashpad snap into. Mine are missing. Continue

1964 429 & Trans For Sale

Started by Russ in For Sale 14 hours ago. 0 Replies

Anyone in need of a 429 & trans? Was running when pulled from car but had low compression on a few cylinders if memory serves me right. Engine/trans are in Phoenix. Russ, 562.858.6926Continue

Center bearing - replacement.

Started by Anders in Restoration Discussion. Last reply by Norman Silverman 18 hours ago. 22 Replies

Had some sound from the propeller shaft and as the rear wheel bearings just been replaced I thought it would be the center bearing. Removed the propeller shaft and checked the center bearing (as per…Continue

Blog Posts

64 Recirc/Fresh Air Door Actuator replaced; FROM THE INSIDE.

Posted by Norman Silverman on February 4, 2019 at 11:21pm 8 Comments

I am happy to report that I have successfully replaced the Fresh Air/Recirc door actuator that is located on the blower box-and have done so without having to remove the blower box. I did it by taking out the glove box and attacking it from the back.  It took several days, LOTS of patience and some band-aids, but it is done. THE most difficult part -BY FAR- is to remove and then replace the screw that sits on the actuator arm, connecting it to the fresh…

Continue

Flashers

Posted by Mike Petrey on January 13, 2019 at 12:25pm 7 Comments

Where do the flashers go in my 64 Deville Convert.  I'm thinking that's why both turn signals stopped working.

Source for Motor mounts and Trans mounts 1964 SDV

Posted by Norman Silverman on January 9, 2019 at 4:23pm 4 Comments

Hi.

Where is the best place to purchase good quality motor mounts/trans mounts for my 1964 SDV? I see that Rock Auto has them for $8 and change, and others for $24 and change. Big difference. Is there a better place to buy them from?

Thanks

Norm

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service