Anyone know where to pick up a harmonic balancer for a 63’ with 390 motor? I have a strange vibration in Park when I hold the pedal at a steady rpm. I’m thinking that may be the issue

Views: 42

Reply to This

Replies to This Discussion

Why do you think it is the balancer causing the vibration ?
Was it ever replaced before that you know of ?

The engine balancer needs to be balanced with the crankshaft assembly so replacing it could have the same result you have now -- a vibration

Enjoy

Well...that’s good info...no I’ve never replaced it....any ideas of what it could be if that’s not what it is?

I have a good balancer with a repair sleeve included.

Shoot me an email with your zip code for a shipping quote.   russ85747@hotmail.com 

When was the tune brought up to spec with all new parts Last time ?

A good tune will be the very best thing to have the engine run smooth as is possible ( reduce vibration ) 

With that done you can look for the next possible solution 

grab the fan  blade and see if it moves front to back as your water pump bearing might be going bad 

Condition of motor and trans mounts ?

engines will move around more in there seat if they are out of tune or a plug is fouling for example due to lack of maintenance which is 6,000 miles for our year cars 

it is a very short interval compared to today car maintenance schedules 

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

Center bearing - replacement.

Started by Anders in Restoration Discussion. Last reply by Norman Silverman 6 hours ago. 23 Replies

Had some sound from the propeller shaft and as the rear wheel bearings just been replaced I thought it would be the center bearing. Removed the propeller shaft and checked the center bearing (as per…Continue

The Central Florida weather could just not get any better !!

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 7 hours ago. 1 Reply

No Description

Wanted: retaining clips for dash pad legs

Started by Mark Geertsma in Wanted to Buy. Last reply by Russ Austin 14 hours ago. 1 Reply

Looking for the retaining clips (L+R) that the "legs" of the dashpad snap into. Mine are missing. Continue

1964 429 & Trans For Sale

Started by Russ in For Sale 22 hours ago. 0 Replies

Anyone in need of a 429 & trans? Was running when pulled from car but had low compression on a few cylinders if memory serves me right. Engine/trans are in Phoenix. Russ, 562.858.6926Continue

Blog Posts

64 Recirc/Fresh Air Door Actuator replaced; FROM THE INSIDE.

Posted by Norman Silverman on February 4, 2019 at 11:21pm 8 Comments

I am happy to report that I have successfully replaced the Fresh Air/Recirc door actuator that is located on the blower box-and have done so without having to remove the blower box. I did it by taking out the glove box and attacking it from the back.  It took several days, LOTS of patience and some band-aids, but it is done. THE most difficult part -BY FAR- is to remove and then replace the screw that sits on the actuator arm, connecting it to the fresh…

Continue

Flashers

Posted by Mike Petrey on January 13, 2019 at 12:25pm 7 Comments

Where do the flashers go in my 64 Deville Convert.  I'm thinking that's why both turn signals stopped working.

Source for Motor mounts and Trans mounts 1964 SDV

Posted by Norman Silverman on January 9, 2019 at 4:23pm 4 Comments

Hi.

Where is the best place to purchase good quality motor mounts/trans mounts for my 1964 SDV? I see that Rock Auto has them for $8 and change, and others for $24 and change. Big difference. Is there a better place to buy them from?

Thanks

Norm

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service