Hi All

just had the valve stem seals done on the 429 with the passenger side head coming off due to a broken bolt.

That is all done and back together.  Now one problem leads to another.  The engine will not idle

or idle adjust as it should.  If I screw the main large idle adjust screw in on the carter the engine still

runs - if I turn the drives side smaller idle air adjust screw all the way in the engine does not stop.

There is a noticeable flat spot right at bottom of idle on take off and the engine just is not right at least

at idle.

Is this an indication of a vacuum leak?  The problem is still there if the PCV valve is off and blocked,

same with other vacuum lines.   Hope that makes sense and I can get some advice.

John

Views: 181

Reply to This

Replies to This Discussion

Great to hear John. If your vacuum advance is original to the car I'd test it with a small cheap vacuum pump. It shouldn't leak down at all. My car ran fine but the vacuum advance was no longer working and was leaking. It ran even better with the fix.

Oh geez, it looks like Tony was correct..... we'll never hear the end of it now. :-) LOL

I do have a surprisingly good track record with trouble shooting problems with our cars having owned mine for 53 years and being on our cars websites since 2006 more often than one time daily
I have a passion for the subject as so many others here and enjoy sharing and helping anyone i think i can to enjoy there car by keeping it rolling down the road
We do have a great team of very knowlegable people who i think can solve any problem these cars may develope and do it on a daily basis
They make this website the great place it is ( even if they delete a post of yours for very bad behavior only once in 11 years ---What The ----- )
You would think someone would have you back after all that time being here and helpful to many
You know like one of the regulars---!!!
I GET NO RESPECT I GET NO RESPECT ( playing with my tie )

Enjoy

Enjoy

Ha Ha Good One!!!!

John

Thank you !

Enjoy

I have never used the sealant — with no issues to note 

enjoy 

Russ

nice job - you nailed that idle problem 

enjoy

Clovis 

good to see you are around makes me all warm and fuzzy to know you are close by  LOL!!

enjoy 

RSS

Photos

  • Add Photos
  • View All

Forum

Replacement trunk lid

Started by Joe DiIaconi in Restoration Discussion. Last reply by Christopher Codd 1 hour ago. 19 Replies

 got got my…Continue

Wits end!

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 5 hours ago. 36 Replies

Well,  after the tire change, car running good......... then on a pleasure cruise for abour 35 miles to my destination.   25 miles in, back end vibration came back home to roost.  I was goung 55 to…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

Brakes Went Out

Posted by Christopher Codd on August 8, 2018 at 8:25am 18 Comments

My '64 Cadillac DeVille had been sitting for awhile while I was travelling this summer and when I came home it had some issues starting. After replacing the plugs and the ignition coil, it was running better than it had in a long time but the brakes were sticking. I noticed the brake pedal was traveling a little farther than usual when slowing down. Soon after I noticed a hissing noise coming from around the brake pedal. Then I lost the brakes pretty much completely. I couldn't find any…

Continue

Tom and Dwight's excellent 64 Fleetwood tales

Posted by Norman Silverman on July 29, 2018 at 2:52pm 1 Comment

Wow, what a great recitation of events-and what a magnificent restoration. 

Thanks for providing a most pleasurable read.

Norm

Comfortron AC trouble shooting

Posted by Norman Silverman on July 23, 2018 at 8:54pm 5 Comments

OK, here we go.....

I got the book to troubleshoot the system. INDISPENSABLE to this effort. 

As I do a cursory exam, I see that the AC RECIRC SOLENOID is Cracked (the WHITE one in the engine compartment coming out of the HVAC body with two vacuum hoses on it). I tried to patch it up (cracked all around the base), but it does not look like it will hold. 

PLEASE TELL ME THAT REPLACING THIS PART IS NOT AS DIFFICULT AS I THINK IT IS, But I think it is a bear to…

Continue

A/C Issue / Stumped !

Posted by Dana G Cooper on July 23, 2018 at 6:29pm 37 Comments

My 63 CDV factory A/C was trash so I replaced every part in the system and converted to R134 . I also installed a STV bypass kit which eliminated the STV all together and converted the system to a cycling system.  I vacumed and charged the system with 36oz of 134. The system is cycling as it should and the pressures are right at 250 high side, cycle off at 25lbs and cycle back on at about 35lbs. It is making plenty of water on the low side hoses and evaporator drain. There is very good air…

Continue

Videos

  • Add Videos
  • View All

© 2018   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service