Hey gang Im a newby to the vintage Caddy group and need some reliable recommended parts sources for both new & used for my '64

Hood stops and window regulators are at the top of the list for now.

Would love to get my clock working again, read that the oil needed to be changed in it from time to time LOL

Any help is greatly appreciated! 

Views: 68

Reply to This

Replies to This Discussion

I have a huge selection of good used parts. I even carry some new parts I had made up for the 63/64.  I also have refurbished clocks. What I have now is a very good condition refurbished clock for 140.00 The chrome is great, and the clock was refurbished by a clocksmith.

Rubber pieces can be found at rubbertherightway.com  steelerubber.com   Regulators usually don't go bad, it is usually dirty dried up grease in the tracks of the windows, and the main gear on the power window motor.

Check out my site www.1963caddyshack.com      Shoot me an email if you need anything.

Thanks Russ I will for sure check out the site! This might sound weird but I'd really like to try and fix the clock that's in it so I can say it's the original but if that all goes south I'll for sure reach out.

I understand about the dried up window tracks. I haven't taken it apart yet so I'm not really sure but the front windows cock out of alignment when going up so I have to hold them in line and then they go up ok, going down seems fine. Rear window seems to be sticking and the drivers side wing window doesn't work at all so I have a few issues to work on.

Thanks again,


Steele Rubber (www.steelerubber.com) sells the hood bumpers complete with the adjustment stud/screw for $7.90 each. (See below for catalog #).  You might check the big name usual suspects such as USA Parts & Supply, OPGI, Kanter, McVeys, Rock Auto … all listed on our parts supplier page at www.parts.6364cadillac.com

I have large selection of the Coupe/Conv door regulators in VG condition for $55 and good strong tested and cleaned and regreased window motors for$ 45, or $90 for the regulator/motor pair.  If interested email me at jasonedge@nc.rr.com.

Many thanks Jason! Nice to know somebody has the parts if need be! I'll get this thing apart and see what it needs exactly. I also have issues to work out with the A/C controller on the dash. The previous owner has managed to change things around. It only blows out of the vents when the lever is pushed all the way over to defrost. When I do that the compressor kicks on (thats a good thing haha) and it blows out of the dash vents not the defrost vents. The system still has freon in it so again thats a good thing but I think the expansion valve is bad. I'm guessing the vents deal is a vacuum issue.

I will check our your website for sure!

Thx again!



Rockauto.com will be about the cheapest for new parts. Whatever they dont have Russ and Jason have been selling to 6364 members for a long time. They are an excellent resource as well as a few other members. Ebay be my last resort for a few things. 

Thanks for taking the time to recommend the guys above, I appreciate it and I'm sure they do as well!




  • Add Photos
  • View All


Looking for wisdom & guidance!

Started by Alex in 1963/64 Cadillac Specific Discussion. Last reply by Kevin Campbell 12 hours ago. 10 Replies

Hello! What a great group! A few years ago I owned a 64 Fleetwood Series 60 special and got hooked! I’m going to be looking for a 63/64 coupe early next year and am just looking for some pointers. I…Continue

July 2018 Newsletter Classifieds: Three Cadillacs for Sale

Started by Jason Edge in For Sale. Last reply by Jason Edge 20 hours ago. 1 Reply

There are Three 1964 Member Cadillacs posted for sale in our July 2018 Newsletter. You can check out the Ads by…Continue

CLC Member Jack Carroll Jan 2019 Hemmings Classic Cars Article

Started by Jason Edge in General Discussion 20 hours ago. 0 Replies

A big tip of the hat to fellow CLC member Jack Carroll and the Jan 2019 Hemmings Classic Cars magazine spotlight on his designs in the 1960's at AMC in the article "History of Automotive Designs:…Continue

New seats for 1963 4 door 4 window

Started by paul k in General Discussion. Last reply by Kevin Campbell yesterday. 1 Reply

I pickup yesterday seats from my local upholstery shop.I did restore springs (remove rust with Rust Mort and paint with POR-15).I have to restore seat transmission etc.-yet.I like how it came out.I…Continue

Blog Posts

Brighter Headlights. What to install that won't draw too much current.

Posted by Norman Silverman on December 15, 2018 at 9:07pm 3 Comments

My car still has its "T-3"headlamps and they shed poor, yellow-tinted light. I'd like to replace them with something that most folks on this web site use, that would shed good light and don't heat up the wiring with too many amps. 

Survey says?


Help with this repair Estimate.

Posted by Dj Lethal on December 13, 2018 at 7:05pm 11 Comments

I recently took my car to a “Cadillac” “Specialist here in Los angles CA.

After leaving my car to diagnose my steering column for not shifting properly. I get this txt from the shop owner. Mind you I just got the car and wanted to at least shift from the column without having to shift for the engine bay. Also wanted to get a price on dash lights to work. Basically I’m trying to feel out if he’s putting gravy on the labor.

Here we go. Parts Labor

Oil pump kit - 225 375… Continue

63/64 Cadillacs for sale

Posted by Frank Herrera on December 10, 2018 at 7:41pm 3 Comments

Hi fellas!!

Well I recently found a guy here locally, who’s got about 8-9 63/64 Cadillacs convertible and hardtop coupes. I also recently found a 64 convertible Eldorado. I really want to purchase it here shortly. If anyone wants to buy it off me or the guy selling it, let me know ASAP. It’s really a great price. If anyone is looking for anything let me know. If you have Instagram my handle is @caddikingheartbreaker. You can also message me on here. I’ll check back from time to time. Or… Continue

Although the radiator was not leaking, nor was the car running hot, I tool out the radiator today to have it boiled out and rodded out. Then I changed the oil and filter (filter is very easy to reach…

Posted by Norman Silverman on December 8, 2018 at 9:29pm 15 Comments

Although the radiator was not leaking, nor was the car running hot, I tool out the radiator today to have it boiled out and rodded out. Then I changed the oil and filter (filter is very easy to reach with the radiator out), then the thermostat got changed. 

I'll have the radiator back from the shop on Monday, and will reinstall it then. 

Still having…



  • Add Videos
  • View All

© 2018   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service