Any tips,tricks,suggestions on what's worked for you to loosen the 11/16 nut on the power steering high pressure hose? I can get a flare wrench on it but access is limited and awkward and t's hard to get enough leverage to loosen. The car is a 64 coupe. Thanks.

Views: 101

Reply to This

Replies to This Discussion

I used a flare wrench and a rubber mallet to lightly tap it loose. It was really on there. 

As Chris suggested a flare nut wrench and a firm tap with a hammer. There are 6 pt and 12 pt flare nut wrenches just like box end wrenches and while I prefer 6 point tools on everything (they strip less) the 12 pt gives you 30 more degrees of angle to work with if you cannot get fitted on nut where you have some room to turn. 

I have a set of these 12 point crows feet that work great for these applications.

Image result for 11/16 12 point crowfoot

I've had mine for years and bought them off a Snap-On truck.

You might try the evil twins....... Amazon or ebay.

Thanks, I'll give the hammer a suggestion a try although there's not a lot of room to swing one. It seems like there would be easier access if the master cylinder was removed. I just gpt done putting it back on, but if that's what it takes I'll take it off again. Anyone resort to that to get the job done?

There is absolutely no room to get a mallet down there to tap on wrench from above. Heck I can barely fit my arm down to get the wrench in position. Then its basically a one hand backhand pull. Wouldn't budge. I was about to point of removing the master cylinder for more access when by the grace of God it broke loose! So now all is good!

I use a crows foot line wrench with a long extension.  Perfect time to go out and buy new tools.

There are only two bolts holding the power steering pump on, and the hose is flexible.  
Now that you have it off, you are going to have more trouble getting the new one one.
Simply remove the pump and avoid all the aggravation.  Leave the line a little loose while you remount the pump, and tighten it after the pump is in place so you know it has clearance.  

I looked at mine and coming from someone that doesn't have time to dilly dally with getting stuff apart as I part a car out, I would If I couldn't brute force it with a standard open/box or flare nut wrench I would a) just wrap a towel up and put against the inner fender frame area to get behind the wrench with a crow bar to break nut free or b) heat a wrench up put a good bend in it to give you better access and turning radius from above, or c) if high pressure line is being replaced cut the pipe close to nut and just use a regular socket or deep socket.  If I were only swapping out the power steering pump I wouldn't touch the hoses at the steering gear... just disconnect at the pump as Mark indicated.   Usually just a bit of leverage is all you need and you have to think thru it and see what you can use.  Reading the 

RSS

Photos

  • Add Photos
  • View All

Forum

'64 Deville Conv. passenger power windows problem

Started by Michael Vogler in 1963/64 Cadillac Specific Discussion. Last reply by Michael Vogler 18 hours ago. 4 Replies

all four power windows work from the driver's control panel, but none of the passenger windows work from the passenger switches.  Is this a master switch problem or an wiring problem?   Thanks for…Continue

Time of year to be checking your antifreeze ( coolant ) numbers —-Nov

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion 23 hours ago. 0 Replies

Good time of year to be checking your coolant to see what temp it will freeze at Giving  you enough time to do a coolant change— if it is time to do so —-or —if your freeze at temp numbers are to…Continue

Tags: check, Coolant

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Interiors in the PNW

Started by keith price in Restoration Discussion. Last reply by Jason Edge yesterday. 3 Replies

Just wondering if anyone knows of a place to get interiors done in the Pacific Northwest. I'm looking at seats, door cards and headliner. I live in the Tacoma Washington area so west side is…Continue

Blog Posts

1964 Cadillac Fleetwood sixty special / transmission dipstick needed

Posted by Pablo on September 20, 2020 at 9:57pm 1 Comment

How are you doing folks, I’m looking for a transmission dipstick, any info I will appreciated, thank you very much

1963 Cadillac hood driver side hinge

Posted by Steven on September 16, 2020 at 9:23am 1 Comment

Hello,

 Does anyone know were I can buy a 1963 Cadillac hood driver side hinge or is there any other hinge that would fit? 

Thanks

Steven

Bad Guage?

Posted by Karl Schwarz on August 26, 2020 at 3:08pm 6 Comments

So I am troubleshooting my fuel gauge issue. I bought a new sender and tested it. It  it goes from 1-ohm (empty) to 35-ohm (full). When I test it (outside the tank), when the float is in the up (full) position it only moves the gauge to about 1/2 full. When at the bottom (empty) position the gauge shows empty. This is the same issue I have when I fill and then use the gas in the tank - the gauge never reads ore than half full. Based on what I've read on this thread it would seem like the…

Continue

Website

Posted by Fritz Seitz on August 11, 2020 at 2:35am 0 Comments

I have been working on a website-----www.fritzsautorepair.com-----

Does anyone have suggestions?

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service