Any tips,tricks,suggestions on what's worked for you to loosen the 11/16 nut on the power steering high pressure hose? I can get a flare wrench on it but access is limited and awkward and t's hard to get enough leverage to loosen. The car is a 64 coupe. Thanks.

Views: 80

Reply to This

Replies to This Discussion

I used a flare wrench and a rubber mallet to lightly tap it loose. It was really on there. 

As Chris suggested a flare nut wrench and a firm tap with a hammer. There are 6 pt and 12 pt flare nut wrenches just like box end wrenches and while I prefer 6 point tools on everything (they strip less) the 12 pt gives you 30 more degrees of angle to work with if you cannot get fitted on nut where you have some room to turn. 

I have a set of these 12 point crows feet that work great for these applications.

Image result for 11/16 12 point crowfoot

I've had mine for years and bought them off a Snap-On truck.

You might try the evil twins....... Amazon or ebay.

Thanks, I'll give the hammer a suggestion a try although there's not a lot of room to swing one. It seems like there would be easier access if the master cylinder was removed. I just gpt done putting it back on, but if that's what it takes I'll take it off again. Anyone resort to that to get the job done?

There is absolutely no room to get a mallet down there to tap on wrench from above. Heck I can barely fit my arm down to get the wrench in position. Then its basically a one hand backhand pull. Wouldn't budge. I was about to point of removing the master cylinder for more access when by the grace of God it broke loose! So now all is good!

I use a crows foot line wrench with a long extension.  Perfect time to go out and buy new tools.

There are only two bolts holding the power steering pump on, and the hose is flexible.  
Now that you have it off, you are going to have more trouble getting the new one one.
Simply remove the pump and avoid all the aggravation.  Leave the line a little loose while you remount the pump, and tighten it after the pump is in place so you know it has clearance.  

I looked at mine and coming from someone that doesn't have time to dilly dally with getting stuff apart as I part a car out, I would If I couldn't brute force it with a standard open/box or flare nut wrench I would a) just wrap a towel up and put against the inner fender frame area to get behind the wrench with a crow bar to break nut free or b) heat a wrench up put a good bend in it to give you better access and turning radius from above, or c) if high pressure line is being replaced cut the pipe close to nut and just use a regular socket or deep socket.  If I were only swapping out the power steering pump I wouldn't touch the hoses at the steering gear... just disconnect at the pump as Mark indicated.   Usually just a bit of leverage is all you need and you have to think thru it and see what you can use.  Reading the 

RSS

Photos

  • Add Photos
  • View All

Forum

The Australian Bushfires:.......

Started by Kevin Campbell in General Discussion. Last reply by Kurt 23 hours ago. 10 Replies

I know we have some Aussies on here and I have to say, Australia, is in a whole world of hurt at the moment, so do ya best to stay safe.Currently, in the southern states, 4 huge fire fronts, look…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

How much play in 63 timing chain?

Started by Ben Roberts in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 yesterday. 4 Replies

I will be installing a new chain and gears because I'm in this deep and all the forums here strongly recommend doing so.  It appears the coating is intact and I don't have to worry about that debris…Continue

Harmonic balancer holes are too shallow for the 3 bolts of puller

Started by Ben Roberts in 1963/64 Cadillac Specific Discussion. Last reply by Ben Roberts on Friday. 3 Replies

Trying to pull 1963 390 harmonic balancer.  The holes needed for the 3 bolts on the puller can only thread in 1/4” which is not enough to run an impact wrench on it.  I ran a tap to clean the threads…Continue

Blog Posts

1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…

Continue

Looking for the Rochester Choke Tube ...

Posted by Mack on January 10, 2020 at 1:14am 3 Comments

37E244B6-71C7-4857-8D50-1BD8C48077A4.jpeg

Looking to buy the choke tube for my Rochester... anybody have one for Sale???

AC/heater for 1964 Cadillac coupe de ville

Posted by Matias J. Adrogue on January 7, 2020 at 11:11am 9 Comments

Good morning!  I am Matias Adrogue.  I bought a 1964 Cadillac coupe de ville last year and am real close to the final restoration details!  I call her “Jaws 64”.  Pics will be posted soon.  I need advise regarding a AC/heater.  It came stock in the vehicle but it does not work.  A mechanic gave me a bid of $1700 to replace and repair.  I am ready to install a new system - Vintage Air or Old Air Products from Fort Worth Texas.  I would greatly appreciate your thoughts.  I read the great write…

Continue

63 cadi conv

Posted by Merlino jean marc on December 31, 2019 at 2:51pm 0 Comments

Hello everyone 

As a European, I fell in love with Americans cars and Americana stuff.

I bought a running 63 for cheap .but there is no secret when you buy cheap ,it is big project. The car needs everything. Overtime I was able to slowing buy parts .actually  I am looking for the passenger front lower section which is becoming harder ,and harder to find

The car has a lot of issue with rust.it needs a paint,a top and I need to replace all floor pans.with patience and…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service