I started her up, let her warm up and then out of no where she died. She still starts up but she wont stay running. I just took apart the entire dash and put everything back together. I dont think I should have messed with anything that would control the idle.  The reason i think i might have blown a gasket is bc when i went to inspect the motor, there was oil on the underside of the carb, oil on the intake manifold and there was white smoke coming out of the old tube in the side (dont know what its for) Im looking for any ideas why she wouldt stay idling and where should i buy my new gaskets? I want metal pref the ones with the blocker plate.

Views: 94

Reply to This

Replies to This Discussion

I dont think I have the Idle Plate for the carb either xD

Kris is the smoke coming out of the intake choke heater hole or the PCV hole? If it's coming out the choke hole you need a new choke tube or if it's not used you need to tap it, bottom and top, and plug it off. If it's the pcv hole it needs to be routed to a manifold vacuum with a pcv hooked inline. 

I do believe its the Choke tube. The pcv line is plugged into my carb. I dont use the choke hole in my current build, whats an easy way to block it off, but still be able to reuse it later bc i dont think its damaged.  

Kris its damaged if you have smoke coming out of choke tube. If you don't want to tap the intake for bolts to block it off the best way to do it is to block off at the heads. I used roofing flashing cut to small squares with rounded corners. Hi temp gasket glue was used to hold everything to the intake and allowed to dry overnight then a slight light coating before going back on the heads. I do it this way to provent them moving around while sealing and helping prevent new leaks. 

Ok, I like the idea of just blocking the head all together. Is the broken choke tube causing a vacuum leak or making the motor run worse? I just want to know what kind of improvement i can expect from removing the choke tube or blocking the heads. 

Do you have an aftermarket carburetor with an elctronic choke? If the gaskets are under the carburetor you should not have a vacuum leak. If you go the route of blocking the exhaust crossover at the heads you have to also hit the heat riser at the exit side of your drivers side exhaust manifold. It directs the exhaust gases through the intake when the car is cold. You really don't need it if the car has an electric choke or is driven only in the summer. You can do a search of the website to get a better understanding of the heat riser. 

I got an eddelbrock 1406 with the electric choke.  So to block the heads i would also have to mess with the heat riser? so in theory it would be easier to just tap the broke choke and put a bolt in it.

I had a '61 Cadillac with a 390 that had a vacuum release parking brake. If yours has that feature (I own a '64 so I don't know about the '63s) maybe the hose came loose when you were rebuilding the dash.

Also, I had a similar vacuum problem with my '61 390. I know the '63 390 is a total re-design 'one year only' model but I am sure Cadillac didn't completely change everything. I took the intake manifold off to find a vacuum plug/port on the underside of the manifold was completely missing or disintegrated.  I have no idea what it ever went to or controlled but I tapped it, plugged it and drove the car happily ever after. 

Lastly, there is a vacuum port on the front of your bakelite carburetor base gasket that often becomes broken or cracked and leads to the problems you describe above. You definitely have a vacuum leak of some nature by the sounds of it, spray some starter fluid around all the carb base with the car running to see if idle increases when you spray over a certain area. If it does, you have found your leak.  Good luck!

Kris I don't believe you need the shim or spacer with the eldebrock carb. If you have the electric choke I would really consider removing the heat riser from your exhaust and blocking the passages at the head and intake gasket. I believe Russ sells the spacer to replace the heat riser with. Just get a cheap set of intake gaskets from rock auto and make your own steel shims to block off the passage. You have to pull the intake to repair the choke tube or tap it to block off with bolts anyway so the shims is easier. 

You need all the same gaskets for the Edelbrock that came stock with the Carter carb ( a regular gasket and metal gasket under the carb )
You need the black spacer under the gaskets ( a regular gasket under thst )
You will have --two places --to connect the PVC hose to now
You need to block the lower of the two off
You can wire the heat riser open to stop it from working

If blocking the heat passage at the head i would block both the top and bottom of the choke tube on the intake as it is off already

The spacers are Very Necessary for the car to run correctly
It will not run right without them installed


Ok, I dont want to block the head passage, bc I dont want to mess with the heat riser, but i do plan on blocking the choke tube and and the passages under the carb. Looks like i need to get the metal shim, I have the black spacer. How would one go about wiring the heat riser open? 

Jason —has a video on here that shows how the heat riser works 

when you see that —just use some wire to keep it open all the time - -that simple ( a very old hot rod trick )

only if you close the heat passage at the head 

do pull the carb off the intake and clean out the passage under the carb if you —do not —seal the heat passage at the head 

if dirty it will improve your start up with a smoother idle especially in colder weather

i have kept my intake stock regarding the heat passages and I do have an Edelbrock 1406 carb with the electric choke 

my feeling is why mess with an engine that performs so well with its stock design 

i did keep this car forever because I enjoy the way it performs in its stock form— myself 




  • Add Photos
  • View All


Rear axle - special transportation device

Started by Anders in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin 2 hours ago. 1 Reply

Needed to replace my rear axle as the old made some weird noice even after replacing the wheel bearings. So in the fall I got another rear axle. Had it blasted and painted and been ready for install…Continue

Tags: axle, rear, tool

She's Almost Done!

Started by Mark Borer in Restoration Discussion. Last reply by Michael Long 3 hours ago. 37 Replies

Hey guysThe convertible finally has some color on it!!Hoping I have it back sometime early next weekThen the long process of putting it back togetherHope you like the picsMarkContinue

Original jack locations

Started by Eli in 1963/64 Cadillac Specific Discussion. Last reply by Anders 8 hours ago. 1 Reply

As I restore this wonderful car, headaches and gaps in knowledge arise that many of you may take for granted. Where might I find pictures of the jack locations on the bumpers and close ups of the…Continue

1963/64 Cadillac Chapter Spotlighted in the May Self-Starter

Started by Jason Edge in Chapter Discussion. Last reply by Tony and Ginny 429 21 hours ago. 9 Replies

The 1963/64 Cadillac Chapter is spotlighted on pages 12-16 in the May issue of Cadillac & LaSalle Club Self-Starter magazine.  If you have a membership level that provides online access to the…Continue

Tags: Starter, spotlight, Self, Chapter, Cadillac

Blog Posts

Oil Stick lenght

Posted by Florentin loic on April 4, 2018 at 5:46am 2 Comments

Hi every one,

After a long time rebuilding my 63 convertible, i finaly get on the road.

A question if anyone can help me. Can somebody tell me the lenght of the motor oil stick.

the cap was probably broken and welded by the old owner. but i m not sure it's in the right place

i put the right amount of oil in motor, but for the weekly maintenance i would like to do two mark "full and add oil"

So i need the lenght from de cap to the two mark

Thanks a…


For sale: 1963 Cadillac front center impact bar $100 + shipping

Posted by Lee Martin on April 3, 2018 at 2:12pm 0 Comments

Offering this newly re-chromed 1963 Cadillac front center impact bar for sale, $100 plus whatever it costs to ship it from Detroit to your location.  

The unit fits perfect on driver's side but does not sit flush on passenger side.  I am told someone needs to take a wooden block and hammer and bang the passenger side lower corner in to make it fit right.  If you know how to do this stuff, this is the piece for you.

Email themidnighthour.tv@gmail.com with any questions.…


429 Cadillac Rod Bolts

Posted by Dave Fundaburg on March 22, 2018 at 8:19pm 1 Comment

Does anybody know of a source for new rod bolts for the 429 or are we stuck with what we have any information would be appreciated. Thanks

seat belts

Posted by dan mcnatty on March 17, 2018 at 4:35pm 3 Comments

I am installing front seat belts in 63 coupe the holes were already in floor but I do not know how to route inner belts it appears they go through seat in middle?did not find how to remove center armrest on seat  are openings there or do you cut into seat? any help or pictures would be great dan


  • Add Videos
  • View All

© 2018   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service