Per Tony,  i am starting a new thread on my adventures with this rear main leak,

i posted a video on a 390 engine of a rear main seal replacement but the engine was out of the car,, gave some insight as to sealing and materials etc.

One of my neighbors has a hoist,(yeah!) and has allowed me to use it,, makes it a lot easier than rolling around on the asphalt in the street and is enough higher that its not too confining under there.  I did have to pay attention to the lift points though as it seems you cant just put those lift arms wherever you want..

As of this evening, I have taken the exhaust loose, the steering loose, and the starter is out,, took about 4 hours to do that.  I guess there is nothing earthshaking to report on any of this.  Tomorrow, I will take the pan off and proceed from there.

To be clear before proceeding.

the 63 manual says to insert the bearings in there slots, do not pull off wax coating as that will aid in insertion.  I do not see any wax on my gasket, so my guess they had it on the old ones.,, 

Now, the question here is,, do i add a touch of oil or something to aid in that insertion process,, the manual does not suggest it, as i describe above, or, just insert dry, as is..

it does say apply rubber cement to cap and block mating surfaces, and gasket ends, but that is the only reference in the 63 manual regarding lubricaitng the seal for installation,,  so is that correct?? insert dry??

the you tube video says to use lubridation after insertion so it wont be dry on start up, so i plan to do that as well.

i will try to take a few photographs of things once i get the pan off,  i m sure most have seen the underside, but its my first venture in there and post them for reference.

Views: 712

Reply to This

Replies to This Discussion

Only very extremely Looooooong  Treads —to be learning from —LOL 

Enjoy 

Which way does exhaust gasket face .? Metal side up or down.  Minewas so degraded, i couldnt tell

Never mind,  i got it figured

RSS

Photos

  • Add Photos
  • View All

Forum

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 6 hours ago. 166 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Cadillac King - UNFAIR, Unprofessional

Started by Edward in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 6 hours ago. 9 Replies

Hi Good America Today I’ll like to bring awareness, and hope to help prevent future headaches. 20years and they still got my order wrong !At Cadillac King i spent over 1400$ on parts. I specifically…Continue

Rear main Follow up replacement and repair,,

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 7 hours ago. 67 Replies

Well, got it all together,, Jason, i was looking in the wrong chapter in the manual on the starter,, got that figured out.  everything hooked back upGot it put back together, started up, and oil…Continue

Movie Star Cars.

Started by Kevin Campbell in General Discussion. Last reply by Kevin Campbell 16 hours ago. 19 Replies

We have the Village Roadshow film studios about an 1.5 hour drive away.They've put out a call for cars to appear in a movie about Elvis. :-)So, I nominated our 64 Fleetwood as a potential "Movie Star…Continue

Blog Posts

Stuck at two red (dash) lights!

Posted by Jeff Kinzler on November 3, 2019 at 10:00pm 9 Comments

I hope someone can help solve these two electrical problems that appeared one after the other.

By way of background: The car, a '64 Eldorado has very limited use. It was at a restoration shop for 15 months until last January-  that supposedly did a bunch of wiring repairs including rebuilding the gas gauge that still hasn't worked properly, and the clock that hasn't worked, and re-soldering the broken wires in the drive door. All window and seat controls appear to be…

Continue

driveshaft help

Posted by wayne weaver on October 9, 2019 at 4:41pm 1 Comment

can anyone help me with a driveshaft ? I have a 1963 Cadillac 62 series 4dr with the hydro-matic trans. I need the male splined shaft on the front of the rear driveshaft section. the piece with the nut attached by clip.id be willing to buy a shaft if its not horribly priced.

Dash removal

Posted by Jake Mickley on October 9, 2019 at 12:06am 9 Comments

Hello everyone,

On a 63 CDV, if a guy wanted to remove the entire dash to get all the metal painted, and do some other things behind there, how would he go about doing that?  I checked here and the shop manual, but can't find a complete guide.

As always, and help or direction is appreciated.  Thanks!

--Jake

Introducing myself

Posted by Gary Marchand on October 7, 2019 at 9:32pm 8 Comments

Thanks for letting me join the club.  Picked up this ‘64 Coupe Deville a few months ago out of Beverly MA, the car has few stickers on it from various Cadillac clubs, didn’t know if anyone might recognize it from it’s “Glory days.” Everything seems pretty healthy except for the body and some very Mickey Mouse repairs, was wondering if anyone had any leads on…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service