Hello,

Purchased new front springs from Springs and things for my 63. Both ends are square cut as opposed to the tapper cut on the originals. My question is where to position the lower spring end?  The service manual has the tapered end falling between the raised bump and the shock center line. doesn't seem right having the spring end hanging off the control arm. I called the company and they confirmed I have the correct springs.

Thank you.

Views: 59

Reply to This

Replies to This Discussion

I'm pretty sure the lower end is installed with the end of the spring tang even with the rear end of the lower control arm +/- 1/2"

Thanks Ronnie, that helps. I installed the right spring as you described, however, the left spring fit better with the end even with the front edge of the control arm. Installing the left like the right caused the top of the spring to push off the spring pocket due to the square end design. Nothing like OEM...

Passenger side spring lower end faces to the front of the control arm located between the raised spot on the control arm and the center of the lower shock bolt. The left drivers side spring lower end goes to the rear of the control arm in the same relation to the lower shock bolt. Hope this helps!

I’m going to try that.  

Thank you

RSS

Photos

  • Add Photos
  • View All

Forum

WTB power steering pump pulley

Started by Chris Codd in 1963/64 Cadillac Specific Discussion. Last reply by Chris Codd 6 hours ago. 2 Replies

My power steering belt pulley sheered the woodruff key off the pump shaft and is pretty wrecked. Does anybody have a pulley for sale? Or the whole pump and pulley together?

Mystery Shake???

Started by Ron Collins in 1963/64 Cadillac Specific Discussion. Last reply by Ron Collins 10 hours ago. 2 Replies

Hello All,Jumped into the mobile after a long winters nap and she shakes!! at or above speeds of about foury mph she shakes like the wheels are out of balance, so I had them rebalanced, still the…Continue

64 Convertible rear seat back

Started by tom servas in 1963/64 Cadillac Specific Discussion 10 hours ago. 0 Replies

Hello , I am re- installing the rear seats in our 64 Convertible and looking for verification of how high/low to install the seat back. Can anyone show a photo of their rear  (upright portion) seat…Continue

Charging the air conditioning with R12

Started by Robert Sweeney in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 16 hours ago. 2 Replies

Hi Guys,The never ending saga continues.I'm thinking that rebuilding the rotary valve has the pneumatic system working now.  I have a vacuum pump and a new filter dryer.  I also borrowed a set of R12…Continue

Blog Posts

Cadillac Returns to its Roots Under New Leadership

Posted by Jeff Kinzler on May 1, 2019 at 12:30am 3 Comments

Cadillac’s new boss says they should stop trying to build BMWs and go back to building Cadillacs again.

What do you think? 

https://carbuzz.com/news/cadillac-finally-admits-what-everyone-knew-for-years

Radiator And Shrouds

Posted by Dominic Salemi on April 24, 2019 at 3:36pm 1 Comment

Hello

Anyone have a decent radiator and shrouds and hardware for a 1964 Cadillac deville. I have an alum. radiator and I'm deciding on to fix it or back to the original one. If I fix it I won't need parts.

Thanks

64 Recirc/Fresh Air Door Actuator replaced; FROM THE INSIDE.

Posted by Norman Silverman on February 4, 2019 at 11:21pm 8 Comments

I am happy to report that I have successfully replaced the Fresh Air/Recirc door actuator that is located on the blower box-and have done so without having to remove the blower box. I did it by taking out the glove box and attacking it from the back.  It took several days, LOTS of patience and some band-aids, but it is done. THE most difficult part -BY FAR- is to remove and then replace the screw that sits on the actuator arm, connecting it to the fresh…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service