hey all

i just finished my restoration 

i am just tweaking things now, and my steering column and dash panels were slightly off

i removed the lower steering column cover and loosened the clamp on the bottom of the column and the 2 bolts inside that hold the column in place

i adjusted it all and tightened up everything

my dash pad went on next and it was way off on the drivers side

i had to readjust the drivers side of the dash frame raising and pushing it towards the firewall 

i accomplished this and then had to readjust the steering column

it looks good but the column still moves a bit

the only thing I am missing is the screw that’s goes into the bottom of the column thru the lower steering wheel cover

any ideas as to what I missed and what that screw does?

i did get the dash pad in better, but the gap by the windshield is greater on the drivers side

thx everyone

Views: 51

Reply to This

Replies to This Discussion

A screw goes in the lower panel. It has a special head to it, and I am out. Any screw will work.

The column is held in place by the clamp under the dash and the column should slide over the collar on the dash wiper switch mount panel.  The bottom of the column is secured by the rag joint and held with 2 bolts.

You should have a large cad coated floor clamp with 3 bolts to floor board and 2 bolts against column. (see 1st picture). There is also a large hanger bracket that attached to firewall/cowl via two nuts to 2 protruding studs, and a hanger bracket at the bottom with one bolt. (see 2nd picture pointing to hanger bracket, with outline if hanger bracket in blue.)
These should be very snug and tight with very little movement of the column once all these bolts are tightened.  Note: The tilt column is a larger diameter column and using the tilt brackets on a non-tilt would cause the column to be lose. If you need any of the brackets, or other mounting hardware give me a shout at jasonedge@nc.rr.com 



  • Add Photos
  • View All


1963 Convertible - No Backup Lights

Started by Karl Schwarz in 1963/64 Cadillac Specific Discussion. Last reply by Charles Fares 34 minutes ago. 1 Reply

The backup lights worked on my '63 Series 62 convertible when I bought it in July, but have stopped working. All other lights work fine. There is no power coming to the connectors behind the license…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 8 hours ago. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

spark plugs

Started by Ron Perry in 1963/64 Cadillac Specific Discussion. Last reply by Ron Perry 23 hours ago. 6 Replies

Gentlemen   I have a 1964 Sedan De Ville with 20 thousand original miles. I am going to replace the spark plugs. What plug would you recommend? I only drive the car a few hundred miles a year and the…Continue

Blog Posts

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…


Road Trip

Posted by Ray Schick on January 21, 2020 at 9:00pm 7 Comments

Got a little cabin fever this morning,decided to take a road trip to Hickory Corners Michigan, The Gilmore Museum. It’s about 2 1/2 hours from my home . Place is awesome,I was really impressed.



1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…


Looking for the Rochester Choke Tube ...

Posted by Mack on January 10, 2020 at 1:14am 3 Comments


Looking to buy the choke tube for my Rochester... anybody have one for Sale???


  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service