while out for a cruise and to a car show, i was heading home, car started sputtering,, would go, then no feel ing of gas, would go a while, then sputter .  i started thinking of quickest way home with out to many stops,  got about 6 blocks and it died.   

it sounded or felt like a car does when you run out of gas, but, that is not possible as I just put gas in it about 2 hours earlier, so i have half a tank, but that is the feeling,,   sputtering, then go, then sputter some more, then go,, then died,

walked home, going back in the truck see if i can get it started with some fuel in carb and sputter it home,

it is not running hot, no other particular symptom.  

would his be most likely fuel pump or blocked fuel filter,, ??

anyway, thought on the above while i go and try to get er home.. I'm just glad i did nt suffer embarrassment of it croaking at the car show as i drove through, but then again,, some one there may have known what it was,, oh well,, 

old cars i guess

Views: 646

Reply to This

Replies to This Discussion

Check your fuel sediment bowl for possible water in the gas. Lots of rain in your area lately  and service station tanks do sometimes get water in them.  Just a suggestion, it happened to me once.

thanks,, will ck,, we have have some rain down here in MS...

as a follow up, i walked home, got some gas, drove back to car,  tried to turn it over, and it fired right up, drove home quickly with no notice of sputter  WTH!!!     let car sit a while, thumped the filter, its a metal one.. and was going to replace with the glass bowl one, but engine was still hot.   anyway, after sitting a while, i turned it on, fired back up, idled for a few minutes, began to run a little rough,  i got out my timing light to see if something was off there, nothing there, still at 5.  going to let it sit, try it again, take it around block, see what happened.. still looking for additional thoughts if water is not culprit,

Replace your metal fuel filter with a new clear one ( watch the fuel flow direction --on it ) and check the debri screen just in front of the fuel line going into the carb
Remove the fuel line at the carb and inspect the screen there --if you have one

Do you have- any idea --what condition the inside of your fuel tank may be in ?

Enjoy

Tony, i chged it out to clear glass oem.  Bulb is full,  i removed an put back that filter at carb a while back, remember it being frail-lish.  Im gonne see if our parts guys here hv a replacemnet.  No clue as to tank other than, its a well maintained exterior , and prior owner was one family since 63.  And was driven simewhat regulalerly.  Not sitting for years, if that matters.  

I did read some prior postings on similar condition.  I hv chged filtercan outvriding   will see if filter chg helped

'How did the ride work out ?

Seemed ok.  Didnt note any sputtering on this effort.  Want to take on a strait stretch for 1o or 15 miles,   but dnt want to get stranded.

On anothr note, my hood insulation has recently come out,  coukd the lack of insulation generate excessive heat around the carb that coukd cause this,  if indeed it reappears,  

I think your problem is fuel deliver
Starting from the gas tank - you have an overflow tube at the front of the gas tank ( near the axel)
Be sure it is in position and the rubber hose is good
From the gas tank to the carb be sure you have no fittings letting air into the fuel line ( tighten and check all conections
Look for a worn or split hose possibly leaking air
Best to change all rubber gas lines for the newer one that are for ethanol fuels when you can
Try driving around very close to home until you see some improvement

Enjoy

will do,, nice weather next few days, so will get under an see whats there

Thanks again

ok back to this issue, the stalling, sputtering, 

i checked hoses as suggested,, rubber ones do look a bit tattered and rough,  i did see the overflow hose as well, it goes up, then curls back downward,, it too was a bit rough.  will get to those after the axle change.

the other night, maybe last night, i took car out circling town on the by passes to keep as a steady push on the pedal to see if i could get a sputter or a stall.. drove for 45 minutes and not one sputter or stall,, i figured it was fixed.

today, took for several 20  30 minute rides, no problem.  

then, out of nowhere i got stuck in traffic, and the heat gauge started to move and ti started sputtering,,, as the temp dropped back to 1/4,, it seemed to settle down and stop.  under normal driving, my temp gauge stayes on the 1/4 mark,, however, if i get stuck in traffic, the heat will move towards the 1/2,, but it never gets to more than half between the 1/4 and 1/2.  an that is when it seems to start the sputtering and stalling.  now this didnt seem to happen until i pulled out the insulation that was sagging out.  so  could that lack of insulation be causing some sort of heat build up around the carburetor.  its the only correlation i can make,  but then again, I'm still in mechanic school for idiots,   so what i think doesnt really count much

Be sure you heat riser at the bottom of the driver side ---exhaust manifold ( were the exhaust pipes bolts up to it ) is opening when your engine gets hot
Wire it open if it does not work correctly
Do not burn yoursellf on the hot manifold
Move it any way you can when the car is cold to see how it feels
( is it smooth or sticking ) and understand its motion --then get it hot and see if it has opened

If the heat riser does not open when it should it will over heat the intake manifold and thin the gas mixture in the carb
Might be the problem

Enjoy

Ok.  I saw that video w the heat gun, and i have seen that part under the car.  Will chk it out

Go to --video - in the header to see a heat riser demonstration by Jason

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 16 hours ago. 173 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Limo rear A/C box needed

Started by Anthony McCarn in Wanted to Buy. Last reply by Anthony McCarn on Saturday. 2 Replies

the case of my rear evaporator box was severely damaged by the p/o of my car. just in need of the case, but will buy a whole unit if the price is right. thanks!Continue

Tags: box, evaporator, conditioning, air, a/c

1963/64 Cadillac Chapter December 2019 Newsletter Posted

Started by Jason Edge in Newsletters. Last reply by Jason Edge on Saturday. 1 Reply

I have just completed and posted the December 2019, 1963/64 Cadillac Chapter Newsletter to our…Continue

Tags: Newsletter, Chapter, 2019, December

Blog Posts

still need a driveshaft

Posted by wayne weaver on November 26, 2019 at 11:53am 2 Comments

well thank you UPS for losing the driveshaft that Russ Austin shipped me. 

however i still need a rear driveshaft section for my 63. mine has a vibration due to the bushing inside of it. its a shame because the ball and sockets in the cardian joints are perfect but it has a woble on the balancing machine. so .  still need the rear section. anyone have a good one ? is there driveshaft alternatives to use ? i am really considering an LS swap and since im fighting the driveshaft search…

Continue

63 guidematic issues

Posted by maurice lapoiinte on November 24, 2019 at 3:10pm 0 Comments

 So my 63 guide matic headlamps stay on low beam all the time. I have so far bypassed the system and everything works normal. I have been thru the trouble shooting in the manual but this is where the confusion begins.on my car when the power relay is powered I have low beam and when its not powered I have highbeam, this appears to be opposite what the diagnosis says should be correct.The wiring is all original and no wires have been mixed up.has anyone ever unplugged the 2 wire connector…

Continue

Another advantage of the Pertronix III

Posted by Doug Scarrow on November 23, 2019 at 11:12am 1 Comment

   Having tried both the II and III I can say the multispark feature of the III offers a smoother idle . It is also easier to install .Does not require removal of the distributor

Stuck at two red (dash) lights!

Posted by Jeff Kinzler on November 3, 2019 at 10:00pm 9 Comments

I hope someone can help solve these two electrical problems that appeared one after the other.

By way of background: The car, a '64 Eldorado has very limited use. It was at a restoration shop for 15 months until last January-  that supposedly did a bunch of wiring repairs including rebuilding the gas gauge that still hasn't worked properly, and the clock that hasn't worked, and re-soldering the broken wires in the drive door. All window and seat controls appear to be…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service