while out for a cruise and to a car show, i was heading home, car started sputtering,, would go, then no feel ing of gas, would go a while, then sputter .  i started thinking of quickest way home with out to many stops,  got about 6 blocks and it died.   

it sounded or felt like a car does when you run out of gas, but, that is not possible as I just put gas in it about 2 hours earlier, so i have half a tank, but that is the feeling,,   sputtering, then go, then sputter some more, then go,, then died,

walked home, going back in the truck see if i can get it started with some fuel in carb and sputter it home,

it is not running hot, no other particular symptom.  

would his be most likely fuel pump or blocked fuel filter,, ??

anyway, thought on the above while i go and try to get er home.. I'm just glad i did nt suffer embarrassment of it croaking at the car show as i drove through, but then again,, some one there may have known what it was,, oh well,, 

old cars i guess

Views: 779

Reply to This

Replies to This Discussion

Check your fuel sediment bowl for possible water in the gas. Lots of rain in your area lately  and service station tanks do sometimes get water in them.  Just a suggestion, it happened to me once.

thanks,, will ck,, we have have some rain down here in MS...

as a follow up, i walked home, got some gas, drove back to car,  tried to turn it over, and it fired right up, drove home quickly with no notice of sputter  WTH!!!     let car sit a while, thumped the filter, its a metal one.. and was going to replace with the glass bowl one, but engine was still hot.   anyway, after sitting a while, i turned it on, fired back up, idled for a few minutes, began to run a little rough,  i got out my timing light to see if something was off there, nothing there, still at 5.  going to let it sit, try it again, take it around block, see what happened.. still looking for additional thoughts if water is not culprit,

Replace your metal fuel filter with a new clear one ( watch the fuel flow direction --on it ) and check the debri screen just in front of the fuel line going into the carb
Remove the fuel line at the carb and inspect the screen there --if you have one

Do you have- any idea --what condition the inside of your fuel tank may be in ?

Enjoy

Tony, i chged it out to clear glass oem.  Bulb is full,  i removed an put back that filter at carb a while back, remember it being frail-lish.  Im gonne see if our parts guys here hv a replacemnet.  No clue as to tank other than, its a well maintained exterior , and prior owner was one family since 63.  And was driven simewhat regulalerly.  Not sitting for years, if that matters.  

I did read some prior postings on similar condition.  I hv chged filtercan outvriding   will see if filter chg helped

'How did the ride work out ?

Seemed ok.  Didnt note any sputtering on this effort.  Want to take on a strait stretch for 1o or 15 miles,   but dnt want to get stranded.

On anothr note, my hood insulation has recently come out,  coukd the lack of insulation generate excessive heat around the carb that coukd cause this,  if indeed it reappears,  

I think your problem is fuel deliver
Starting from the gas tank - you have an overflow tube at the front of the gas tank ( near the axel)
Be sure it is in position and the rubber hose is good
From the gas tank to the carb be sure you have no fittings letting air into the fuel line ( tighten and check all conections
Look for a worn or split hose possibly leaking air
Best to change all rubber gas lines for the newer one that are for ethanol fuels when you can
Try driving around very close to home until you see some improvement

Enjoy

will do,, nice weather next few days, so will get under an see whats there

Thanks again

ok back to this issue, the stalling, sputtering, 

i checked hoses as suggested,, rubber ones do look a bit tattered and rough,  i did see the overflow hose as well, it goes up, then curls back downward,, it too was a bit rough.  will get to those after the axle change.

the other night, maybe last night, i took car out circling town on the by passes to keep as a steady push on the pedal to see if i could get a sputter or a stall.. drove for 45 minutes and not one sputter or stall,, i figured it was fixed.

today, took for several 20  30 minute rides, no problem.  

then, out of nowhere i got stuck in traffic, and the heat gauge started to move and ti started sputtering,,, as the temp dropped back to 1/4,, it seemed to settle down and stop.  under normal driving, my temp gauge stayes on the 1/4 mark,, however, if i get stuck in traffic, the heat will move towards the 1/2,, but it never gets to more than half between the 1/4 and 1/2.  an that is when it seems to start the sputtering and stalling.  now this didnt seem to happen until i pulled out the insulation that was sagging out.  so  could that lack of insulation be causing some sort of heat build up around the carburetor.  its the only correlation i can make,  but then again, I'm still in mechanic school for idiots,   so what i think doesnt really count much

Be sure you heat riser at the bottom of the driver side ---exhaust manifold ( were the exhaust pipes bolts up to it ) is opening when your engine gets hot
Wire it open if it does not work correctly
Do not burn yoursellf on the hot manifold
Move it any way you can when the car is cold to see how it feels
( is it smooth or sticking ) and understand its motion --then get it hot and see if it has opened

If the heat riser does not open when it should it will over heat the intake manifold and thin the gas mixture in the carb
Might be the problem

Enjoy

Ok.  I saw that video w the heat gun, and i have seen that part under the car.  Will chk it out

Go to --video - in the header to see a heat riser demonstration by Jason

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

63 coupedebille fuel pump issues

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 4 hours ago. 20 Replies

I have a 63 cadillac and I took it to a mechanic for a motor tune up long story short the fuel pump gave out and hes tried twice to order it and he says it didnt fit the original pump is smaller on…Continue

A Before & After Example

Started by Jason Edge in Restoration Discussion yesterday. 0 Replies

Since I started cadmium plating the many fasteners and other items from the 55 and counting parts cars I have bought in (1200 lbs worth and counting), I have to say it has really taken the…Continue

Oil leaking out of oil cap breather

Started by mark zimmerman in Restoration Discussion. Last reply by mark zimmerman yesterday. 12 Replies

Hi i would like some ideas on this i replaced oil cap breather and pcv valve and still oil  coming out of breather at normal speeds down the road.This has been going on for quiet awhile from the…Continue

Update on fuel pump

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by William R Conte yesterday. 1 Reply

I'm still looking thru land and sea for this fuel pump anyone out there know what size engine I have here are some pics of the stamps on the block I found to make sure my engine is a 390 because the…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service