Suspension Illustrations from Shop Manual
(Click on Pictures to Enlarge)
 

1963-64 FRONT SUSPENSION

1963 Rear Suspension
(Note Difference in Control Links for 1964 below)

1964 Rear Suspension

Below Are More Front and Rear Suspension Component Pictures from the Shop Manual:


1963 Rear Lower Control Link
(again, Note difference from 1964 Rear Lower Control Link below)

1964 Rear Lower Control Link

Views: 767

Reply to This

Replies to This Discussion

Excellent reference material for those about to embark on a total front or rear suspension rebuild. Notice the rear upper yoke and its position once installed. If you put the ball joint in upside down the yoke will almost fit. Do not make this mistake as you will fight for an hour trying to get the nut on the ball stud to no avail.

Please don't ask how I know this tidbit of information!

what would be your reason for rebuilding this... understand, i am complete novice,, what parts would you be trying to repair if you were doing a rebuild.  What would be going wrong ?

The bushings, ball joints, shocks, coil springs and other moving parts of the suspension physically wear out and need to be replaced over time.  This can cause tire wear, steering and handling issues, which in turn can become dangerous especially with these larger heavy older cars. Items that often get replaces are shocks, coil springs, upper and lower ball joints, upper and lower control arm bushings, tie-strut bushings, idler arm, center link, and tie rods. I replaced all of my front end suspension components about 10 years ago on my 64 CDV, and it went from a very hard to handle, loose car, that drifted all over the place to one I can now drive anywhere with one finger... and on bias ply tires! 

Question: I want to purchase upper control arm bushings for my 64 with AC. There are two sizes sold; 1 7/8 outside diameter and 1 1/2 outside diameter. I am going to assume the bigger bushings were installed in cars with factory AC. Is that correct or was there just a mid year change?

Thanks

As far as I can tell they had nothing to do with AC or non-AC and do not know the rhyme or reason just that you find either size on the cars. You need to measure the outer diameter of the sleeve the bushing fits as seen in the illustration below which shows a 1 1/2".  You can use a caliper, open end wrench (if you have one big enough) or an adjustable wrench and measure tape.

Thanks

When you say drive with one finger that is so very true
I do the same thing and it makes this heavy car seem so much lighter and agile than it Should ever be otherwise

Don't you just love the feel of your 63-64 rolling down the road driving with one finger

Enjoy

Hello Guys, I'm looking for a 1963 Coupe Deville 2 door lower right suspension control link. Any suggestions in Houston Texas? Or anywhere else. I figured Houston was a booming oil city and must of enjoyed these Caddy's in large amounts. thanks for your time and effort.

I have VG rear lower 63 control links for $50 + s/h.  If interested email me at jasonedge@nc.rr.com with shipping address.

There is another option available lately. Russ Austin is manufacturing a new control link with a better bushings than original. Read this post before you decide:

Testing new rear lower control arms.

I think  Russ will be able to help you with the part right here 

He is in Austin and should be along shortly 

Enjoy 

Tony.

Russ family name is Austin. He does not live in Austin or in Texas. Russ Austin that posts great help/suggestions and sell parts on this site lives in Arizona.

RSS

Photos

  • Add Photos
  • View All

Forum

Wanted: retaining clips for dash pad legs

Started by Mark Geertsma in Wanted to Buy. Last reply by Russ Austin 6 hours ago. 1 Reply

Looking for the retaining clips (L+R) that the "legs" of the dashpad snap into. Mine are missing. Continue

1964 429 & Trans For Sale

Started by Russ in For Sale 14 hours ago. 0 Replies

Anyone in need of a 429 & trans? Was running when pulled from car but had low compression on a few cylinders if memory serves me right. Engine/trans are in Phoenix. Russ, 562.858.6926Continue

Center bearing - replacement.

Started by Anders in Restoration Discussion. Last reply by Norman Silverman 17 hours ago. 22 Replies

Had some sound from the propeller shaft and as the rear wheel bearings just been replaced I thought it would be the center bearing. Removed the propeller shaft and checked the center bearing (as per…Continue

1964 coupe de ville trunk v emblem

Started by ANGELO MARTINEZ in Restoration Discussion. Last reply by James jacques yesterday. 1 Reply

hello I am looking for the v emblem on a 1964 coupe de ville trunk  v emblemthank youContinue

Blog Posts

64 Recirc/Fresh Air Door Actuator replaced; FROM THE INSIDE.

Posted by Norman Silverman on February 4, 2019 at 11:21pm 8 Comments

I am happy to report that I have successfully replaced the Fresh Air/Recirc door actuator that is located on the blower box-and have done so without having to remove the blower box. I did it by taking out the glove box and attacking it from the back.  It took several days, LOTS of patience and some band-aids, but it is done. THE most difficult part -BY FAR- is to remove and then replace the screw that sits on the actuator arm, connecting it to the fresh…

Continue

Flashers

Posted by Mike Petrey on January 13, 2019 at 12:25pm 7 Comments

Where do the flashers go in my 64 Deville Convert.  I'm thinking that's why both turn signals stopped working.

Source for Motor mounts and Trans mounts 1964 SDV

Posted by Norman Silverman on January 9, 2019 at 4:23pm 4 Comments

Hi.

Where is the best place to purchase good quality motor mounts/trans mounts for my 1964 SDV? I see that Rock Auto has them for $8 and change, and others for $24 and change. Big difference. Is there a better place to buy them from?

Thanks

Norm

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service