Suspension Illustrations from Shop Manual
(Click on Pictures to Enlarge)
 

1963-64 FRONT SUSPENSION

1963 Rear Suspension
(Note Difference in Control Links for 1964 below)

1964 Rear Suspension

Below Are More Front and Rear Suspension Component Pictures from the Shop Manual:


1963 Rear Lower Control Link
(again, Note difference from 1964 Rear Lower Control Link below)

1964 Rear Lower Control Link

Views: 1199

Reply to This

Replies to This Discussion

Excellent reference material for those about to embark on a total front or rear suspension rebuild. Notice the rear upper yoke and its position once installed. If you put the ball joint in upside down the yoke will almost fit. Do not make this mistake as you will fight for an hour trying to get the nut on the ball stud to no avail.

Please don't ask how I know this tidbit of information!

what would be your reason for rebuilding this... understand, i am complete novice,, what parts would you be trying to repair if you were doing a rebuild.  What would be going wrong ?

The bushings, ball joints, shocks, coil springs and other moving parts of the suspension physically wear out and need to be replaced over time.  This can cause tire wear, steering and handling issues, which in turn can become dangerous especially with these larger heavy older cars. Items that often get replaces are shocks, coil springs, upper and lower ball joints, upper and lower control arm bushings, tie-strut bushings, idler arm, center link, and tie rods. I replaced all of my front end suspension components about 10 years ago on my 64 CDV, and it went from a very hard to handle, loose car, that drifted all over the place to one I can now drive anywhere with one finger... and on bias ply tires! 

Question: I want to purchase upper control arm bushings for my 64 with AC. There are two sizes sold; 1 7/8 outside diameter and 1 1/2 outside diameter. I am going to assume the bigger bushings were installed in cars with factory AC. Is that correct or was there just a mid year change?

Thanks

As far as I can tell they had nothing to do with AC or non-AC and do not know the rhyme or reason just that you find either size on the cars. You need to measure the outer diameter of the sleeve the bushing fits as seen in the illustration below which shows a 1 1/2".  You can use a caliper, open end wrench (if you have one big enough) or an adjustable wrench and measure tape.

Thanks

When you say drive with one finger that is so very true
I do the same thing and it makes this heavy car seem so much lighter and agile than it Should ever be otherwise

Don't you just love the feel of your 63-64 rolling down the road driving with one finger

Enjoy

Hello Guys, I'm looking for a 1963 Coupe Deville 2 door lower right suspension control link. Any suggestions in Houston Texas? Or anywhere else. I figured Houston was a booming oil city and must of enjoyed these Caddy's in large amounts. thanks for your time and effort.

I have VG rear lower 63 control links for $50 + s/h.  If interested email me at jasonedge@nc.rr.com with shipping address.

There is another option available lately. Russ Austin is manufacturing a new control link with a better bushings than original. Read this post before you decide:

Testing new rear lower control arms.

I think  Russ will be able to help you with the part right here 

He is in Austin and should be along shortly 

Enjoy 

Tony.

Russ family name is Austin. He does not live in Austin or in Texas. Russ Austin that posts great help/suggestions and sell parts on this site lives in Arizona.

RSS

Photos

  • Add Photos
  • View All

Forum

Engine and tranny seals

Started by Klutch in Restoration Discussion. Last reply by Tony and Ginny 429 8 hours ago. 54 Replies

Hey guys.Im going to be pulling my engine and tranny out soon. Theres some leaks on my engine and tranny. The main reason for this is because i need to paint the engine and engine bay. So i might as…Continue

1963 Convertible - No Backup Lights

Started by Karl Schwarz in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin 10 hours ago. 2 Replies

The backup lights worked on my '63 Series 62 convertible when I bought it in July, but have stopped working. All other lights work fine. There is no power coming to the connectors behind the license…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 20 hours ago. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…

Continue

Road Trip

Posted by Ray Schick on January 21, 2020 at 9:00pm 7 Comments

Got a little cabin fever this morning,decided to take a road trip to Hickory Corners Michigan, The Gilmore Museum. It’s about 2 1/2 hours from my home . Place is awesome,I was really impressed.

9A648CFF-E965-4CE0-8E91-8E194AC70DED.jpeg…



Continue

1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…

Continue

Looking for the Rochester Choke Tube ...

Posted by Mack on January 10, 2020 at 1:14am 3 Comments

37E244B6-71C7-4857-8D50-1BD8C48077A4.jpeg

Looking to buy the choke tube for my Rochester... anybody have one for Sale???

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service