What would be the correct placement of the throttle spring on my '63 30? I can't seem to get the engine to go back to idle unless I push up on the gas pedal. Pics would be great. Many thanks.

Views: 1442

Reply to This

Replies to This Discussion

Do lube the hindge of the gas peddle ,at its base
Floor rust or dirt can be preventing the peddle from moving as freely as it might
Rust buster type spray works and a vacuum
Be sure the flooring is not starting to fail there ,and is still solid
Sure you will have the pictures of the throttle spring you need up soon ,from the boy here

thanks

The throttle return spring attaches to a bracket off the left rear intake bolt as seen below. The spring in the pictures is a stronger than factory spring I had run on mine for some time. I believe I am not running the factory spring that is a bit weaker.  I often see this bracket missing on parts cars that have went through intake replacement and someone forgot to replace the bracket or lost it and have attached the spring to something else. Check to see if you have your return spring setup in this  manner. If you need that bracket, I have a ton of them... for $5 + s/h. I also have an assortment of springs.

Thanks again Jason, I do have the bracket on the intake but the one on the carb is different.

That's an Edelbrock carb you see there so ignore it. On both the Edelbrock, and stock Carter AFB and Rochester 4GC carbs, the throttle rod goes through the throttle plate on side of carb, and the spring simply goes through a hole through the rod. That is there is no additional bracket.

Here is a stock setup on a Carter AFB showing how the return spring looks through the end of the throttle rod where it comes trough the carb throttle plate:

I added those last two pictures to our Carb Help Article at http://6364cadillac.ning.com/profiles/blogs/carburtors-used-in-1963...

Also on AC equipped cars check that the idle speed-up control on right side of carb is working properly. When the AC is on, it shuts off vacuum to the actuator, allowing the plunger to extend out and push the throttle lever causing idle to increase to 900 to 950 rpm (if set to factory specs).   When the AC is off, you should have full vacuum to the actuator pulling it back in. If you simply disconnect that vacuum line it will allow the plunger to push the idle up as if the AC were on. I remember way, way back on a 64 SDV I owned it took me some time to figure out that the AC Speed-up control was making my car idle very fast all the time.  

I have the Rochester carb which also has the TV rod connected to the carb linkage

Make sure the throttle dash pot is not causing the throttle to stay above idle. It may be rusted or not working at all.

ok

RSS

Photos

  • Add Photos
  • View All

Forum

1964 Cadillac Deville - TH400 kickdown switch

Started by Louis in Wanted to Buy. Last reply by Charles Fares 9 hours ago. 1 Reply

Hello,I am searching for a  TH400 transmission kickdown switch (the one near the carburetor). A new one or in good condition.I already asked Fatsco and US Parts Supply but they don’t have this…Continue

New Gallery

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion 11 hours ago. 0 Replies

I am truly fascinated by the  wonderful  inspiring stories behind owning these 63-64 CLASSIC ANTIQUE CADILLACSThey have set the website ON FIRE !!Jason Mr Webmaster your talents regarding the subject…Continue

64 429 Thermostat Housing

Started by Jason A in General Discussion. Last reply by Russ Austin 14 hours ago. 1 Reply

Does anyone know where to find a thermostat housing for a 64 429?  Are any cars interchangeable?  Chevy 350 looks identical, but a lil bigger.Thanks,JasonContinue

New photo gallery

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 17 hours ago. 8 Replies

Having trouble posting my picture in the new gallery but managed to get the text right The computer WIZ - I am NOT ! Stay safe my friends Continue

Blog Posts

How to sensibly deal with the Corona Virus

Posted by Jeff Kinzler on March 14, 2020 at 5:02pm 6 Comments

https://theamericanscholar.org/covid-19-a-primer/

I found this very helpful, written by a knowledgeable authority in public health. 

Remember, Viruses are not spread by Cadillacs so get out and drive!


Safe & Healthy travels. 

Jeff Kinzler

1963 Eldorado convertible boot

Posted by Les Eastling on February 27, 2020 at 10:33am 1 Comment

I need a used convertible boot for a 63 Cadillac convertible - condition or color is not an issue since it will be used as a pattern for making a new one. One from either a 62 series convertible or an Eldorado would work. I know I am searching for hen's teeth here... but you never know unless you ask!

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service