I have a 64 and the timing is to far advanced  the vacuum advance hits the valve cover I think this is a result of my father in law having a timing chain put on years ago what is the best remedy ? Pull out housing and reposition it ? Also trying to figure out if maybe they installed the wires  wrong  where exactly should rotor be pointing on TDC ?  and is it possible if it was installed off  that the wires could of been moved on the cap  to make it run .have had this car 27 years and always runs hot and won't start till the engine cools down ( like it is to far advanced  haven't thrown a light on it yet I am doing my homework so when I tackle it I am prepared  I have seen the diagrams here but doesn't really show  clock position of rotor on tdc  any advise is appreciated 

Views: 566

Reply to This

Replies to This Discussion

OK thnk I got the reply and post down  sucks being newbee 

You must have a 1964 series 62 car as they came through with the Jetaway transmission that was used in all Cadillacs from 1956-63 and the 1964 series 62 cars.  DeVille models had the new Turbo Hydramatic which today we call the TH400. 

If you have access to a shop manual, there is a section in there regarding adjusting the linkage to the transmission.  I would be that if you Google it, you will also find the answer. 

This site is great for tech advice, don't be shy. There are always people willing to help you keep it alive and if you decide to sell, there is a section on the site for that as well.

All the best,

Mike 

OK  I am back at it this thing is just Idling to fast  I got totally fed up with it last time now I have to do something with it   but if it runs for 10 mins  it is to hot to restart  It starts and runs fine  It is just to fast at idle  I am at wits end and this car will be causing to have a stroke  I know there must be answers I just can't find them  the carb linkage looks nothing like any posted  and the motors manual I have doesn't address  this problem 

Steve, these cars can be frustrating for sure!  For now, you can disconnect the throttle linkage entirely in order to idle the engine, set the timing, adjust the carb etc.  It sounds like someone may have switched the linkage on you or it is way out of adjustment?  Super fast idle could also indicate a vacuum leak, especially if you hear a "whooshing" sound around the base of the carb.

If you could post a photo of the linkage that may help with diagnosis or identification.

 Thanks I will do that thank you very much for responding 

here they are 

Attachments:

OK I found it  was a cracked hose going to the PCV valve and a bad PCV plugged the port on the carb  now my question is where does the PCV go  it appears to be a hose that disappears under the intake . also can some one point me to detailed instructions for adjusting that TV  down shift rod  my car is holding gears to long I let up on petal and it shifts  a little like a bad modulator valve on a ford  ( my motors only shows a picture of it )  Thanks all for your help 

Steve, you are correct. The PCV hose connects to a breather tube under the intake manifold, towards the rear of the engine.  To access, you will probably have to remove the intake. You may want to replace the hose at this point since you are digging in this far and probably do not want to touch it again. 

You said you have a Motors manual?  I am not sure what year manual you have but the shift linkage from Cadillac '56-'64 Hydramatic (Jetaway) are nearly identical and you can look at the transmission section of the manual for any of those years to see the correct adjustment. Your transmission was used on the series 62 Cadillacs in 1964 and was called a Hydramatic whereas the identical transmission was known as a Jetaway when used in Olds, Buick and Pontiacs. This was the last year Cadillac used that trans in any cars as the Coupe DeVilles used a TH-400 in '64 which became standard across the board in '65.  Best of luck!

The PCV was spliced into that hose and tucked under the manifold  the hose going under seems OK  I just caped the port on the carb to get it to the right Idle when the new PCV comes I should be able to cut that hose back a little and make a new piece between the PCV and carb  as far as linkage gonna dig into that next   I know one way is faster and the other slower  Thanks for the info  I greatly appreciate it 

Steve
What model is the car and where is it located ?

Enjoy

not sure  no name on it  it has 4 doors cloth  seats  and that transmission pretty sure the engine is a 390 her grandmother bought it new in 64  it has been garage kept iout side Chicago since about 1980

Tell us the VIN and we tell what you have, or you can find out yourself from this list:

Suggest you buy a Cadillac Shop Manual if you gonna keep fixing this car.

RSS

Photos

  • Add Photos
  • View All

Forum

63 coupedebille fuel pump issues

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 5 hours ago. 20 Replies

I have a 63 cadillac and I took it to a mechanic for a motor tune up long story short the fuel pump gave out and hes tried twice to order it and he says it didnt fit the original pump is smaller on…Continue

A Before & After Example

Started by Jason Edge in Restoration Discussion yesterday. 0 Replies

Since I started cadmium plating the many fasteners and other items from the 55 and counting parts cars I have bought in (1200 lbs worth and counting), I have to say it has really taken the…Continue

Oil leaking out of oil cap breather

Started by mark zimmerman in Restoration Discussion. Last reply by mark zimmerman yesterday. 12 Replies

Hi i would like some ideas on this i replaced oil cap breather and pcv valve and still oil  coming out of breather at normal speeds down the road.This has been going on for quiet awhile from the…Continue

Update on fuel pump

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by William R Conte yesterday. 1 Reply

I'm still looking thru land and sea for this fuel pump anyone out there know what size engine I have here are some pics of the stamps on the block I found to make sure my engine is a 390 because the…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service