I have a 64 and the timing is to far advanced  the vacuum advance hits the valve cover I think this is a result of my father in law having a timing chain put on years ago what is the best remedy ? Pull out housing and reposition it ? Also trying to figure out if maybe they installed the wires  wrong  where exactly should rotor be pointing on TDC ?  and is it possible if it was installed off  that the wires could of been moved on the cap  to make it run .have had this car 27 years and always runs hot and won't start till the engine cools down ( like it is to far advanced  haven't thrown a light on it yet I am doing my homework so when I tackle it I am prepared  I have seen the diagrams here but doesn't really show  clock position of rotor on tdc  any advise is appreciated 

Views: 375

Reply to This

Replies to This Discussion

 I am getting it in shape to sell I am nearing retirement and going to be moving  and won't have a place to keep it  Thanks for the info 

What one would be a 4 door hard top  62 Sedan ?

Steve
The 4 door would be a Sedan
The engine in 64 - WB a 429 and have the hydramatic trans behind it in the Sedan model
The 390 and 429 look the same in the engine bay as the internals of the 429 are stroked to increase cubic inches
There are 4 and 6 window Sedans in 64

If you post pictures --and what you are looking for regarding price -you may develope some interest in the car here -if seliing the car is the direction you choose to go with it

You might want to get it -road worthy and see if this is something you might enjoy to drive and continue to own and restore
These cars are a very unnique driving experiences
You might be very surprised at the attention and interest in these cars these days when out and about
The interest in the car will be --surprising once you get it out on the road and are using it to enjoy the day
Many will spend hours and dollars restoring a car like this ( which has its frustrating moments ) only to realize it is driving the car and the enjoyment it brings on so many levels that makes up for the blood sweet and tears that go into the restoration process
It does help a lot to be able to do a lot of the wrenching --youself And have the space tools and be willing to invest the time and money the hobby will requires

Enjoy

One of the very best TOOLS  to work on these cars is a shop manual for your year car 

RSS

Photos

  • Add Photos
  • View All

Forum

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 10 minutes ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

How much play in 63 timing chain?

Started by Ben Roberts in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 8 hours ago. 4 Replies

I will be installing a new chain and gears because I'm in this deep and all the forums here strongly recommend doing so.  It appears the coating is intact and I don't have to worry about that debris…Continue

Harmonic balancer holes are too shallow for the 3 bolts of puller

Started by Ben Roberts in 1963/64 Cadillac Specific Discussion. Last reply by Ben Roberts 21 hours ago. 3 Replies

Trying to pull 1963 390 harmonic balancer.  The holes needed for the 3 bolts on the puller can only thread in 1/4” which is not enough to run an impact wrench on it.  I ran a tap to clean the threads…Continue

G-1 differential, $150

Started by Jimmy Davis in For Sale. Last reply by Jimmy Davis on Thursday. 5 Replies

G-1 positraction differential, needs blasting and paint. $150. Pickup Huntsville AL or LTL, I recommend Averitt express. Send me zip for shipping quote.***Update- Sorry if you have tried to contact…Continue

Tags: differential, Rear, G-1

Blog Posts

1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…

Continue

Looking for the Rochester Choke Tube ...

Posted by Mack on January 10, 2020 at 1:14am 3 Comments

37E244B6-71C7-4857-8D50-1BD8C48077A4.jpeg

Looking to buy the choke tube for my Rochester... anybody have one for Sale???

AC/heater for 1964 Cadillac coupe de ville

Posted by Matias J. Adrogue on January 7, 2020 at 11:11am 9 Comments

Good morning!  I am Matias Adrogue.  I bought a 1964 Cadillac coupe de ville last year and am real close to the final restoration details!  I call her “Jaws 64”.  Pics will be posted soon.  I need advise regarding a AC/heater.  It came stock in the vehicle but it does not work.  A mechanic gave me a bid of $1700 to replace and repair.  I am ready to install a new system - Vintage Air or Old Air Products from Fort Worth Texas.  I would greatly appreciate your thoughts.  I read the great write…

Continue

63 cadi conv

Posted by Merlino jean marc on December 31, 2019 at 2:51pm 0 Comments

Hello everyone 

As a European, I fell in love with Americans cars and Americana stuff.

I bought a running 63 for cheap .but there is no secret when you buy cheap ,it is big project. The car needs everything. Overtime I was able to slowing buy parts .actually  I am looking for the passenger front lower section which is becoming harder ,and harder to find

The car has a lot of issue with rust.it needs a paint,a top and I need to replace all floor pans.with patience and…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service